623984
7
Zoom out
Zoom in
Previous page
1/12
Next page
5
Setting Up and Using Your
Stage 5 Series System
The basic procedure for setting up and using your Stage 5 Series Wireless System takes only a
few minutes:
1. For the Stage 5 Series system to work correctly, both the receiver and transmitter must be set
to the same channel. Remove all packing materials (save them in case of need for future service)
and check to make sure that the supplied receiver and transmitter are set to the same channel.
If these channels do not match, contact your Samson Technical Support at 1-800-372-6766.
2. Physically place the receiver where it will be used (the general rule of thumb is to maintain
“line of sight” between the receiver and transmitter so that the person using or wearing the
transmitter can see the receiver). - Extend the antenna and place it in a vertical position.
3. Make sure the Power on-off switch in your HT5 handheld transmitter is set to “Off.
4. On the HT5 handheld transmitter, unscrew the bottom section of the microphone by turning
it counterclockwise and then slide it off.
5. Place a fresh 9-volt alkaline battery in the transmitter battery holder, taking care to observe
the polarity markings. Replace the bottom section of the HT5 handheld microphone by sliding
it on and then screwing it back on. Leave the transmitter off for the moment.
6. Make the physical cable connection between the SR5 output jack and the line audio input of
your amplifier or mixer using the included 1/4-inch cable. If you are connecting to a professional
mixer you can use the balanced XLR jack (with an optional XLR mic cable), be sure to set the
receiver rear panel Audio Output Level switch correctly. If required, both the balanced and
unbalanced outputs can be used simultaneously. Leave your amplifier (and/or mixer) off at this
time.
7. Turn the Volume knob on the SR5 completely counterclockwise. Using the strain relief,
connect the supplied AC adapter to the DC Input on the rear panel of the SR5, then plug the
adapter into any standard AC outlet. Press the front panel Power switch to turn on the SR5; the
green “Power” LED will light up, but all other front panel LEDs will remain unlit
8. Turn on the power to the HT5 transmitter (using its Power on-off switch); all three Battery
strength LEDs will light if the battery is sufficiently strong. At this point, the RF Meter on the
front panel of the receiver will light.
9. Now it’s time to set the audio levels. Turn on your connected amplifier and/or mixer but
keep its volume all the way down. Next, make sure that your HT5 transmitter is unmuted by
setting its Audio switch to “On. Then set the Volume knob on the SR5 fully counterclockwise.
Speak or sing into the mic at a normal performance level while observing the SR5 front panel
Audio Meter. If the “0” (unity gain) segment is lighting steadily, with just occasional higher
excursions, the audio level is correctly set. If not, use the supplied plastic screwdriver to slowly
adjust the HT5 Gain control (trimpot) until the SR5 Audio Meter “0” (unity gain) segment lights
steadily (with occasional higher excursions). Then slowly raise the SR5 Volume knob to the 2
oclock position (unity gain) and, finally, set the volume of your amplifier/mixer until the desired
level is reached.
Bear in mind also that the HT5H microphone is unidirectional which means it picks up sound
from the front of the mic and rejects sound from the rear. This will help reduce the chance of
feedback. In general, you can avoid feedback by taking care not to use any microphone directly
in front of a PA speaker (if this is unavoidable, try using an equalizer to attenuate those high- or
mid-range frequencies which are causing the feedback squealing”).
10. If you hear distortion at the desired volume level (or if the “+6” segment LED in the
Audio Meter is lighting frequently), first check that the SR5 rear panel Audio Output Level switch
is set correctly. Next, make sure that the gain structure of your audio system is correctly set
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson Stage 5H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson Stage 5H in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info