629803
7
Zoom out
Zoom in
Previous page
1/16
Next page
5
Guided Tour - Rear Panel
1: RCA Input connectors
You can connect unbalanced incoming signals to the Servo series using the RCA connectors, which
are wired as follows: Pin 2 (or Tip) hot, and Pin 1 (or Sleeve) ground. The Servo Series accepts input levels of any strength but
needs at least -10dBV dBu to achieve maximum power. Stereo signals should be connected to both the Channel 1 and Channel
2 input jacks; however, when operating the Servo Series in Bridged mode, use the Channel 1 input jack only. See page 8 in this
manual for more information about Bridge mode and page 9 in this manual for full interconnection instructions.
2: Fan
- This variable-speed fan provides vital cooling to your Servo Series (the hotter the amp gets, the faster the fan blows!).
Make sure that both the front and rear panels are kept free of all obstructions and that cool, fresh air is accessible at all times.
Also, try to ensure that the Servo Series is used in a dust-free environment.
3: 1/4-inch Output Connectors
- Use these to connect each channel of the Servo Series to, 4-ohm or 8-ohm loudspeakers with
1/4-inch input jacks. See page 8 in this manual for more information about Bridged mode and page 9 in this manual for full
speaker connection instructions.
4: 5-way Binding Post
- Use these to connect each channel of the Servo Series to 4-ohm or 8-ohm loudspeakers. Be sure to con-
nect the loudspeaker correctly, with the red (+) terminal normally connected to the positive input of the speaker and the black
(ground) terminal normally connected to the negative input of the speaker. See page 8 in this manual for more information
about Bridge mode and page 9 in this manual for full speaker connection instructions
5: 1/4-inch Input Connectors
- Connect incoming signals to these electronically balanced inputs, using the 1/4” TRS (Tip/Ring/
Sleeve) plugs, wired as follows: Pin 2 (or Tip) hot, Pin 3 (or Ring) cold, and Pin 1 (or Sleeve) ground. We recommend the use of bal-
anced three-conductor cabling wherever possible (unbalanced two-conductor 1/4” plugs can also be inserted into these inputs,
but you’ll get better signal quality and less outside noise and hum if you use balanced lines). The Servo Series accepts input levels
of any strength but needs at least +4 dBu to achieve maximum power. Stereo signals should be connected to both the Channel
1 and Channel 2 input jacks; however, when operating the Servo Series in Bridged mode, use the Channel 1 input jack only. See
page 8 in this manual for more information about Bridge mode and page 9 in this manual for full interconnection instructions.
6: AC input
- Connect the supplied heavy-gauge 3-pin “IEC” power cable here.
7: Bridge / Stereo switch
- For normal operation, place this two-way switch in its lower (“STEREO”) position. When placed in its
upper (“BRIDGE”) position, the signal arriving at the Channel 1 input only is again routed to both power amplifiers (again, the
Channel 2 input is ignored), but the two power amplifiers are bridged together. For more information, see the “Bridge Mode”
section on page 8 in this manual and the “Servo Series Connections” section on page 9 in this manual. WARNING: Due to the
extremely high power output of the Servo Series when used in Bridge mode, be sure to use only loudspeakers sufficiently rated to
handle the resultant wattage (in Bridge mode, these must be 8-ohm speakers).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson SERVO 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson SERVO 600 in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info