629825
8
Zoom out
Zoom in
Previous page
1/16
Next page
Guided Tour - Rear Panel
1: Fan - This variable-speed fan provides vital cooling to your PG Series (the hotter the amp gets, the faster the fan blows!). Make
sure that both the front and rear panels are kept free of all obstructions and that cool, fresh air is accessible at all times. Also, try
to ensure that the PG Series is used in a dust-free environment.
2: Input connectors - Connect incoming signals to these electronically balanced connectors, using either XLR or 1/4" TRS (Tip/
Ring/Sleeve) plugs, wired as follows: Pin 2 (or Tip) hot, Pin 3 (or Ring) cold, and Pin 1 (or Sleeve) ground. We recommend the use
of balanced three-conductor cabling wherever possible (unbalanced two-conductor 1/4" plugs can also be inserted into these
inputs, but you’ll get better signal quality and less outside noise and hum if you use balanced lines). The PG Series accepts input
levels of any strength but needs at least +4 dBu to achieve maximum power. Stereo signals should be connected to both the
Channel 1 and Channel 2 input jacks; however, when operating the PG Series in Bridge or Parallel modes, use the Channel 1 input
jack only. See page 9 in this manual for more information about Parallel mode and pages 10 and 11 in this manual for full inter-
connection instructions.
3: Low Frequency Filter - This toggle switch is used to engage a low cut filter, 12 dB per octave at 30 Hz.
4: 5-way Binding Post - Use these to connect each channel of the PG Series to 4-ohm or 8-ohm loudspeakers. Be sure to con-
nect the loudspeaker correctly, with the red (+) terminal normally connected to the positive input of the speaker and the black
(ground) terminal normally connected to the negative input of the speaker. See page 9 in this manual for more information
about Bridge mode and pages 10 and 11 in this manual for full speaker connection instructions.
5: Circuit Breaker - This circuit breaker will trip if there is a fault with the mains voltage or if maximum output is exceeded (very
highly distorted). Push it in (once only!) to restart the amplifier after a short rest period.
6: AC input - Connect the supplied heavy-gauge 3-pin “IEC power cable here.
7: Speakon™ output connectors - Alternatively, you can use these to connect each channel of the PG Series to 4 or 8-ohm
loudspeakers. See page 9 in this manual for more information about Bridge mode and pages 10 and 11 in this manual for full
Speakon™ connector wiring and interconnection instructions.
8: Bridge / Stereo / Parallel switch - For normal operation, place this three-way switch in its center (“STEREO”) position. When
placed in its left (“PARALLEL”) position, the signal arriving at the Channel 1 input only is routed to the power amplifiers of both
Channel 1 and Channel 2 (the Channel 2 input is ignored). When placed in its right (“BRIDGE”) position, the signal arriving at the
Channel 1 input only is again routed to both power amplifiers (again, the Channel 2 input is ignored), but the two power amplifi-
ers are bridged together. For more information, see the “Bridge and Parallel Modes section on page 9 in this manual and the “PG
Series Connections” section on pages 10 -11 in this manual. WARNING: Due to the extremely high power output of the PG Series
when used in Bridge mode, be sure to use only loudspeakers sufficiently rated to handle the resultant wattage (in Bridge mode,
these must be 4 or 8-ohm speakers).
9: Limiter - This toggle switch is used to engage the Limter circuit, an automatic dynamics processor used to hold the input signal
at a fixed threshold level which helps keep a clean signal and protect the connected speakers.
1
2 43 15
6792 8
4
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson PG2200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson PG2200 in the language / languages: English as an attachment in your email.

The manual is 2,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info