23499

Samson MDR1248 Manual

9
Zoom out
Zoom in
Previous page
1/28
Next page
5
Front Panel Controls
FRONT PANEL
1 MIC IN
– Input connector for Low-Noise Microphone
pre-amp.
2 LINE IN–Input connector for Line level inputs.
3 INSERT – 1/4-inch TRS (TIP/RING/SLEEVE) connector
providing send and receive channel patch point for
outboard effects.
4 GAIN
– Used to set the input level of the mic pre and
line input.
5 LOW CUT – Bass roll off switch at 75Hz used to elimi-
nate unwanted low end rumble and hum.
6 HIGH FREQUENCY
– Controls the high band of the
Channel Equalizer, +/- 15 dB at 12KHz.
7 MID CUT/BOOST – This control knob provides +/- 15
dB of boost or cut at the frequency set on the MID
SWEEP control on the mono input channels.
8 MID SWEEP – Control knob used to set the center
frequency of the mid band of the Channel Equalizer.
9 LOW FREQUENCY – Controls the low band of the
Channel Equalizer, +/- 15 dB at 80Hz.
10 AUX 1 – Auxiliary send that can be used with an
external effects processor, or to create a cue or moni-
tor mix.
11 PRE / POST switch
– Used to configure Aux 1 signal
routing from a Pre fader to a post fader send.
12 AUX 2/DSP – Post-fader auxiliary send that can be
used with an external effects processor, or to create a
cue or monitor mix, or to send a signal to the internal
DSP.
13 PAN – Controls the channel’s position between left
and right in the stereo bus.
14 3/4 MUTE LED
– When illuminated, the display indi-
cates that the input channel is assigned to the ALT3/4
bus and is muted in the Left /Right Main Mix bus.
15 3/4 / MUTE switch
– When engaged, the input chan-
nel is assigned to the ALT3/4 bus and is muted in the
Left / Right MAIN MIX bus.
16 SOLO LED
– When illuminated, the display indicates
that the input channel is assigned to the SOLO bus.
17 SOLO switch – When engaged, the input channel is
assigned to the SOLO bus.
18 PEAK – Red LED will illuminate indicating when the
GAIN has been adjusted too high.
19 LEVEL
– Audio taper fader provides smooth control
of level changes.
20 +4 / -10 switch – Used to set the line input sensitiv-
ity from –10dB when the switch is pressed in to +4dB
when this switch is out.
21 RIGHT LINE – 1/4-inch phone input connector for the
right line input for the stereo channels.
22 LEFT/MONO LINE - 1/4-inch phone input connec-
tor for the Left Line input for the stereo channels or a
mono input.
23 ALT 3/4 OUTPUTS jacks – Balanced, 1/4-inch phone
connectors carrying the signal from the ALT 3/4 bus.
24 CONTROL ROOM OUTPUT
– Left and Right Control
Room output connectors for connecting a monitor
system.
25 MAIN MIX OUTPUT (1/4-inch) – Left and Right Main
Mix balanced output 1/4-inch TRS connectors.
26 MAIN MIX OUTPUT (XLR)
– Left and Right Main Mix
balanced output XLR connectors.
27 AUX RETURN 1 – Left and right input jacks for con-
necting to the outputs of external line level sources
like those from effects processors.
28 AUX RETURN 2 – Left and right input jacks for con-
necting to the outputs of external line level sources
like those from effects processors.
29 FOOTSWITCH JACK
– 1/4-inch phone jack for con-
necting a standard footswitch used to turn the inter-
nal DSP effects on and off.
30 PHONES JACK
– Connect stereo headphones here.
31 AUX SEND 2 – Line level output from the Auxiliary 2
bus.
32 AUX SEND 1
– Line level output from the Auxiliary 1
bus.
33 2 TRACK OUTPUTS – Connect to the input of a DAT,
Cassette, Mini Disk or Hard Disk Recording system.
34 2 TRACK INPUTS – Connect the output from a DAT,
Cassette, Mini Disk or Hard Disk Recording system.
35 2 TRK LEVEL – Control knob used to set the level of
the source connected to the 2-track input.
36 VARIATIONS – Control knob used to select one of the
sixteen variations for each of the sixteen DSP effect
programs.
37 PROGRAMS – Control knob used to select one of the
sixteen DSP effect programs.
38 DSP PEAK
– LED indicator illuminates when the input
signal to the internal DSP is reaching an overload
level.
39 DSP MUTE switch – Used to turn the internal DSP
effects on and off.
40 ALT 3/4 TO MIX – Routes the ALT 3/4 to the Left /
Right MAIN MIX outputs. Use the ALT3/4 Level (55) to
set the volume.
41 2 TRK TO MIX
- Routes the Left / Right 2 track inputs
to the Left / Right MAIN MIX outputs. Use the 2 TRK
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson MDR1248 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson MDR1248 in the language / languages: English as an attachment in your email.

The manual is 6,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Samson MDR1248

Samson MDR1248 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info