629745

Samson Live L1212 Manual

13
Zoom out
Zoom in
Previous page
1/76
Next page
ENGLISH
9
Controls and Functions
The following section details each part of the LIVE series INPUT section including the MIC and LINE inputs,
the two-band EQ, as well as the MIC and LINE LEVEL controls.
1. MIC LEVEL (L612 and L615 only)
The L612 and L615’s MIC LEVEL
controls the overall level of the
microphone input. Raise the
MIC Level to adjust the volume
of the microphone connected
to the MIC input.
IMPORTANT NOTE!!:
Be sure to keep
the MIC LEVEL control all the way off
if there is no microphone connected.
2. PEAK LED
The PEAK LED will illuminate
RED when the LIVE series Mic
or Line input is receiving a clipped signal. If the PEAK LED lights up, lower the Mic or Line Level control.
Once the PEAK LED goes off, raise the level controls back up until just before the PEAK LED lights.
3. DYNAMIC PROTECTION
The AMP / CLIP
LED is a dual color LED used to monitor the output of the LIVE Series’ internal power
amplifiers. When the unit is first powered on, the AMP / CLIP LED will light red (indicating the output
relay is open). After the soft-start circuitry activates and the output relay closes, the AMP / CLIP will
change to bright green indicating the unit is ready for operation. The LED will flash red on signal power
peaks, while the green LED is still on. If there is a failure condition, the output relay opens and the LED
will switch to solid red, indicating a fault. If this happens, contact your authorized Samson Audio Service
Center.
4. LINE LEVEL
The LIVE Series’ LINE LEVEL controls the overall level of the LINE input. Raise the LINE Level to adjust the
volume of the signal connected to the LINE input.
Using the Equalizer Section (L612, L612M and L615 only)
The L612, L612M and L615 input channels feature a 2-band equalizer allowing you to adjust the high and
low frequencies independently. The channel’s frequency response is flat when the knobs are in the "12:00"
position. You can set a “music” curve by adding a little boost to both the LOW and HIGH frequency. When
using the L612M as a vocal monitor, try a little cut on the LOW and HIGH frequency to remove unwanted
bass and treble for a more focused mid-range response. For most applications, it’s best to start with the LOW
and HIGH controls set flat (12:00 position) and then use the HIGH and LOW EQ in small amounts until you
reach the sound you want.
5. LOW
Rotating the LOW knob towards the right will boost the bass frequencies at 100Hz by 12dB, and
rotating it towards the left will cut the bass frequencies at 100Hz by 12dB.
6. HIGH
Rotating the HIGH knob towards the right will boost the treble frequencies at 10kHz by 12dB, and
rotating it towards the left will cut the treble frequencies at 10kHz by 12dB.
Operating the Live Series
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson Live L1212 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson Live L1212 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 9,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info