624005
17
Zoom out
Zoom in
Previous page
1/24
Next page
13
13 - GROUP INSERT - 1/4-inch Send and Return
jack
Send and return patch point on TRS (TIP/RING/
SLEEVE) jack for interfacing external effects proces-
sors on GROUP bus outputs. The signal is sent on the
tip (the Send) and returns (the Return) on the ring of
the connector.
14 - MAIN INSERT (Left and Right) - 1/4-inch Send
and Return jack
Send and return patch point on TRS (TIP/RING/
SLEEVE) jack for interfacing external effects proces-
sors on Left and Right MIX bus. The signal is sent on
the tip (the Send) and returns (the Return) on the
ring of the connector.
15 - MAIN OUT – 1/4-inch jacks
The L1200 and L2000’s stereo MAIN mix is sent to
the LEFT and RIGHT MAIN OUT ¼-inch phone con-
nectors. The signal level at these MAIN OUT connec-
tors follows the MAIN volume fader. In a live sound
application, you can drive a speaker system using
the MAIN OUT outputs connected to a power ampli-
fier or powered speakers. The signal at the MAIN
OUT jacks follows the MAIN volume fader.
TRS phone jack connector pin-out - Sleeve: Ground,
Tip: Hot (+), Ring: Cold (-)
16 - USB BUS POWER – socket
Plug any USB bus powered lamp here.
17 – FOOTSWITCH - 1/4-inch jack
With a footswitch connected to this jack, you can
turn on and off the on-board digital effects by sim-
ply stepping on the footswitch.
18– PHONES - 1/4-inch jack (top Panel)
Connect standard stereo headphone, 60 to 600
Ohms, here.
Rear Panel
19 - MAIN OUT – XLR connector
The L1200 and L2000’s stereo MAIN mix is sent to
the rear panel LEFT and RIGHT MAIN OUT XLR con-
nectors. The signal level at these MAIN OUT connec-
tors follows the MAIN volume fader. In a live sound
application, you can drive a speaker system using
the MAIN OUT outputs connected to a power ampli-
fier or powered speakers.
XLR connector pin-out - Pin 1: Ground, Pin 2: Hot (+),
Pin 3: Cold (-)
20 - SUBWOOFER OUT – XLR connector
If your sound system includes a subwoofer, you can
use the rear panel SUBWOOFER OUT to conveniently
connect to the amplifier or powered-sub input. The
L1200 and L2000’s stereo MAIN mix is sent, in mono,
to the SUBWOOFER OUT XLR connector. A high-cut
(or low-pass) filter, 12dB at 75 Hz, is applied to this
output to roll off the high frequencies and send
just low frequencies, so no additional crossover is
required. The signal at the SUBWOOFER OUT jacks
follows the MAIN volume fader.
XLR connector pin-out - Pin 1: Ground, Pin 2: Hot (+),
Pin 3: Cold (-)
21 – USB PORT Connect standard standard USB
cable here.
L1200 and L2000 Input and Output Connections
19 20 21
7
7
17
716
18
15
14
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson L2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson L2000 in the language / languages: English as an attachment in your email.

The manual is 4,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Samson L2000

Samson L2000 User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info