630024

Samson Graphite 25 Manual

24
Zoom out
Zoom in
Previous page
1/36
Next page
24
Performance Controls
The Graphite 25 features eight assignable encoders (E1–E8), volume slider (S1), four function but-
tons (F1–F4) and transport controls. Below is a brief description of how these features operate.
Encoders
The factory setting for the encoders is pan control, set to channels 1–4. When you rotate the
knob of an encoder, the encoder number and the data will be shown in the Operation area of the
display. Rotate the knob clockwise to increase the value, and counter-clockwise to decrease the
value (ranging 0–127). You can change parameters or assign other controls to encoders in “Setup
Mode” on page 17. The default settings for encoders are listed in “Factory Default Settings” on
page 31.
Slider
The factory setting for the slider is master volume. When you move a slider, the slider number, S1,
and the data will be shown in the Operation area of the display. Move the slider to the right to
increase the value, and to the left to decrease the value (ranging 0–127). You can change param-
eters or assign other controls to encoders in “Setup Mode” on page 17.
Note: Assign the Channel to “-“ for the slider and encoders to follow the keyboard channel of Zone 1.
Function Buttons
There are four function buttons (F1–F4) on the control panel. The buttons can be dened as
“Note” type (abbreviated to N), which send note messages when pressed, or “Control” type (ab-
breviated to C), which send control messages when pressed.
The buttons can also be set to “Toggle” (abbreviated to 0). Press one of the buttons to send the
On message, and press the button again to send the O message. The buttons can alternatively
be set to “Momentary” (abbreviated to M). If the button is a control type, press the button to send
the control code. When you release the button, the control code will no longer be sent. If the type
of the button is a note type, press the button to send note on message and release the button to
send a note o message.
The button number and value will be shown in the Operation and Data area of the display. The
function of each button is assignable. You can change parameters or assign other controls to
buttons through the setup function. Please refer to “Setup Mode” on page 17 for details. The
default settings for the function buttons are listed in “Factory Default Settings” on page 31.
BANK Buttons
There are four banks of encoders and function buttons with individual settings, expanding the
amount of controls available. The BANK buttons allow you to group the settings of the encoders
E1–E8 and function buttons F1–F4 into a bank, and then recall them quickly. Press the BANK ◀ /
▶ buttons to select between the banks. The bank number will be shown under the BANK tag in
the display. The default bank is 1.
CHANNEL Buttons
Press the CHANNEL ◀ / ▶ buttons to increase or decrease the channel number for all encoders
E1–E8 and function buttons F1–F4 in the activated bank, to quickly expand the working range,
globally. The channel change message will be handled by the computer software when a soft-
ware preset is selected, and the icon “-“ will be displayed under the Ch +/– tag.
Note: When the remote control preset (Preset 2–10) is activated, the BANK and CHANNEL buttons will
send specic control messages to the music software.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson Graphite 25 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson Graphite 25 in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info