624002
9
Zoom out
Zoom in
Previous page
1/92
Next page
9
XP800 • Portable PA System
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO
Mixer Layout
will cut the high frequency response by 15 dB.
LOW Frequency – The LOW knob controls the amount of bass applied to each chan-
nel. The channel’s low frequency response is flat when the knob is in the center
detent (12:00) position. Rotating the knob to the right will boost the channel’s low
frequency response below 100 Hz by 15 dB, and rotating it towards the left will cut
the low frequency response by 15 dB.
6. EFFECTS Knobs – Use the EFFECTS control knows to add an effect to a Mic or Line
input on any of the first four input channels. As the knob is rotated clockwise, the
level of signal sent to the effects bus is increased.
7. LEVEL Knobs – This knob sets the overall level for the input channel.
NOTE: To reduce noise, set the LEVEL controls on any unused channels to the mini-
mum setting.
8. Stereo Channel Input Jacks (channels 5/6, 7/8) – For stereo inputs, use the L input to
connect the left channel and the R input to connect the right channel. Use these
inputs to connect high impedance microphones, synthesizers, drum machines,
MP3, CD, tape players or any other line level device. The XP800 features ¼”
phone,
¹
/
8
” phone, and RCA connectors.
9. MONITOR OUT Jacks – The signal present at the MONITOR OUT jacks is sent from
the MONITOR level control knob, which is fed from the input channels. The
MASTER control does not affect the MONITOR OUT signal. This output can be
used to send the mix to powered speaker cabinets to use a stage monitors, or as
additional front of house speakers to expand the coverage of the system.
10. SUB OUT Connector – This full-range output is used to send the main mix to an
external active subwoofer. The signal present at this connector is the after the
MASTER level control.
11. FOOT SW Jack – Connect a footswitch to this jack to turn on and off the on–board
digital effects.
12. SPEAKER OUT Jacks – Two ¼” phone powered output jacks used to connect the left
and right speakers. Use the included speaker cables to connect the speakers.
CAUTION: The total impedance load for each side of the amplifier must not be less
than 8 Ohms. Do not connect additional speakers to the XP800 mixer/amplifier.
13. AC Input – Connect the supplied heavy gauge 3-pin “IEC” power cable here.
14. POWER Switch – Use the POWER switch to turn power to the XP800 on or off. The
switch illuminates red when the unit is in the ON position and receiving power.
15. MONITOR Level Knob – The MONITOR level control is used to control the overall level
sent to the MONITOR OUT.
16. Pairing Indicator – Displays the Bluetooth
status of the XP800 system.
17. Pairing Button – Press this button to enable discoverable mode in order to pair with
a Bluetooth audio device.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson Expedition XP800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson Expedition XP800 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 13,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info