630000
9
Zoom out
Zoom in
Previous page
1/28
Next page
7
Setting-up the D3500
Press the GLOBAL control switch once or twice until you
see the Inp.
Use the Data Wheel to select OPT 1 or OPT 2.
NOTE:
Once you make an edit to the Global set-up, the red
GLOBAL LED will flash indicating that a change has been
made to the original set-up. You will also see that the red
STORE LED is illuminated
.
To keep the new changes, press the STORE button and
you will exit the GLOBAL mode and both the STORE and
GLOBAL LED’s will turn off.
Using the Left, Right and Link Control Switches
Since the D3500 is a two-channel unit, you can use it as
a stereo, or dual mono equalizer if you are running two
monitor mixes. Depending on the operating mode you set
up in the Global menu, you may want to have the left and
right channels operate together, or individually. The LEFT,
RIGHT and LINK switches will help you operate the D3500
easily and give you the control you need to quickly make
changes and control either one or both sides. The state of
these switches will determine which of the left and right
signals are affected by the hardware control surface and
which channel's parameters are diplayed in the LCD.
Using the LINK switch
If you want to set the D3500 so that the phyiscal hardware
controls and all the parameter controls adjust both the
Left and Right side, press the LINK switch so that the green
LED is lit. Now, when you operate any of the controls, ei-
ther the EQ control knobs or the digital effects, you will be
making the same change on the left and right sides.
If you want to use the D3500 as a dual mono equalizer and
control the Left and Right sides individually, keep the LINK
switch OFF so that the green LED is not lit.
Controlling the Right Channel signal
If you want to control the EQ and the effects for the right
channel individually, make sure the LINK switch is OFF.
Now, press the RIGHT switch to assign the hardware con-
trol surface to the signal connected to the right channel.
With the RIGHT switch selected on and the LINK switch off,
the D3500 controls will edit just the right channel filters
and right channel parameters when accessing the various
menus.
Controlling the Left Channel signal
If you want to control the EQ and the effects for the left
channel individually, make sure the LINK switch is OFF.
Now, press the LEFT switch to assign the hardware control
surface to the signal connected to the left channel. With
the LEFT switch selected on and the LINK switch off, the
D3500 controls will edit just the left channel filters and left
channel parameters when accessing the various menus.
Keep in mind that the LEFT or RIGHT switch determines
which channel's parameters are displayed in the LCD.
Therefore, even if the LINK is on, you can still use the LEFT
and RIGHT switches to select which sides parameters are
displayed in the LCD. This becomes important if you set
the Left or Right channel to a different parameter and then
link them. For example, it is possible to set the same filter
setting for both sides using LINK, then unlink and change
the Gain of one filter on one side. If you press the LINK
again the hardware will control both sides, however the
GAIN will be offset. You can see this by using the LEFT and
RIGHT switches when LINK is on.
D3500_ownman_v1_2.indd 7 9/4/05 5:20:05 PM
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson D-3500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson D-3500 in the language / languages: English as an attachment in your email.

The manual is 7,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info