629766

Samson Auro X15D Manual

10
Zoom out
Zoom in
Previous page
1/72
Next page
10
10. HPF Switch - This switch adjust the High Pass Filter frequency of the cabinet. When using the
Auro speaker with a subwoofer, set the switch to 80Hz or 120Hz depending on the specification
of the subwoofer. It is also recommended to set the HPF to 120Hz when using the Auro speaker
as a floor monitor to limit the low frequency build up on the stage.
11. LIMITER Indicator - This YELLOW LED lights when the amp is near the clipping point and the
limiter is engaged. If the LIMITER indicator lights frequently, turn down the Master VOL control
or INPUT VOL controls on the Auro speaker or turn down the signal at the source, until the
indicator does not light anymore, or lights only occasionally with high signal peaks.
12. FAULT Indicator - This LED lights RED when the input is overloaded, amp overheats or other
problems have been detected. If the FAULT indicator lights due to the amp overheating, the
amplifier will limit the audio and lower the output level. When the unit cools, the FAULT indicator
will turn off and the amplifier will raise the level back up.
13. Line Output - Male XLR connector used to link multiple Auro cabinets.
NOTE: When connecting a loudspeaker to the Line Output of the Auro X12D or X15D, it is important to
power on the main Auro loudspeaker first, then power on the linked speaker. When powering down the
system, it is recommended to turn off all linked speakers, then power off the main Auro loudspeaker.
14. MIX 1/2 & THRU Switch - This switch is used to select the signal that is sent to the Line Output.
When the switch is in the up (MIX 1/2) position, the signal on the Line Output is a mix of both
the Input 1 and Input 2 signals. When the switch is in the down (THRU) position the Line Output
carries only the Input 2 signal.
15. Power Switch - This rocker switch turns on and off the Auro’s main power. The switch lights RED
when the amp is active.
NOTE: It is important to remember the Golden Rule of audio… “LAST ON, FIRST OFF.” Translated, this
means that when turning on your system, you should always turn your powered speakers on LAST, and
when turning your system off, turn your powered speakers off FIRST. This helps avoid any loud pops
caused by inrush current at power up, or down, which can sometimes damage loudspeakers.
16. Fuse Cover - The fuse is located behind the fuse cover. Always replace fuses with the same type of
fuse.
17. AC Power Inlet - Connect the supplied standard 3-prong IEC power cable here.
Note: Never disconnect the plug’s ground pin. It is dangerous and can result in electric shock!
Rear Panel Layout
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson Auro X15D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson Auro X15D in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 12,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info