735246
2
Zoom out
Zoom in
Previous page
1/2
Next page
Temporary Override Mode
Hourly temperature Override Mode (+Hr)
RT510TX thermostat pairing with the receiver Installer Mode
Manual Mode and setting setpoint temperature
Frost Protection
Sleep mode
Holiday Mode
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
2
4
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
1
3
Using or button set a new setpoint
temperature for override.
Using or buttons set new setpoint
temperature.
Press three buttons at the same time
for 3 seconds.
Use or button to set the number
of days for Holiday Mode.
Using or buttons set new setpoint
temperature.
Press +Hr button to set number of hours for
temperature override (e.g. to set up override
for 3 hours, press the button 3 times).
Press the + Hr button until number of hours
disappears from display.
Press button to activate the Manual Mode.
Hold down button for 3 seconds
to activate the Holiday Mode.
Press button to turn On Frost
Protection mode.
Press button again to turn
O Frost Protection mode.
Press SET button
to conrm.
Press SET button to conrm.
You can set up to 31 days.
Using SELECT button choose the parameter.
Press SET to conrm.
Using or buttons set a parameter value.
Press any key to deactivate sleep mode. Thermostat will return to the previous mode.
Thermostat is in sleep mode.
After new setpoint temperature set,
thermostat will return to the main screen.
After new setpoint temperature set,
thermostat will return to the main screen.
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
This function is available only in automatic mode (schedule). If a new setpoint temperature will be set
during the schedule - it will be maintained until next time interval starts according to programmed
schedule.
In this mode thermostat does not work according to the programmed schedule but it will maintain
selected temperature.
In this mode the “frost protection temperature is maintained for a specic number of days.
This function is available in Automatic and Manual Mode. It is used to change the setpoint temperature
for a specied number of hours (up to 9 hours). Once that time is over, thermostat returns to previous
mode.
Turning o hourly temperature override mode before time’s up
Turning O the Frost Protection Mode
Begin the pairing process
End the pairing process
Test the pairing process
Temporary Override mode will be disabled when new schedule will be set.
To turn o the Manual Mode press button. Once the manual mode is o, the hand icon on
the thermostat will disappear.
To turn o the Holiday Mode, hold down button for 3 seconds. The airplane icon should
disappear from the display.
Temperature of the Frost Protection mode is set as default at 5°C. This temperature can be changed
in Installer Mode in d03 parameter.
When the sleep mode is activated, all thermostat functions are paused.
If you bought the RT510TX+ and RXRT510+ separately or if you want to re-pair thermostat with the
receiver, make sure that the device is disconnected from the power supply and the switches on the
receiver have been set to AUTO and ON. Then connect the receiver to the power supply and wait for
the red LED to light steadily. Then switch to the OFF position and again to ON position quickly. The red
ashing LED will conrm entering the pairing mode.
2
2
4
4
1
1
3
3
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
3 sec
3 sec 3 sec
3 sec
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
Note: If you are using the RT510RF+ pack, the pairing between the thermostat and the receiver is already done.
dxx Function Parameter Default value
d01 Temperature display increments 0.1°C or 0.5°C 0.5°C
d02 Temperature oset +/- 3.0°C 0.0°C
d03 Frost Protection setpoint temperature 5.0°C - 17.0°C 5.0°C
d04 Programmer selection 5/2 or 24 hr (7d) 52d
TEST / PAIRING
SELECT SET
Press TEST / PAIRING button to check the
connection with the receiver.
ON
AUTO
OFF
MANUAL
1 sec
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
3 sec
3 sec
Hold and buttons simultaneously
for 3 seconds to start the sleep mode.
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
2
4
1
3
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
Press SELECT to conrm.
Follow steps 2-5, to set next parameters.
To exit the installer mode, wait 10 seconds
- thermostat will return automatically
to the main screen.
65
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
WED
TEST / PAIRING
SELECT SET
WED
TEST / PAIRING
SELECT SET
WED
TEST / PAIRING
SELECT SET
WED
TEST / PAIRING
SELECT SET
WED
TEST / PAIRING
SELECT SET
WED
TEST / PAIRING
SELECT SET
WED
TEST / PAIRING
SELECT SET
WED
TEST / PAIRING
SELECT SET
SAT
Reset of the RT510+ thermostat
Press the RESET button once. You can use a paper
clip. Your thermostat will be reset and will start up
automatically.
RESET
SELECT SET
TEST / PAIRING
SELECT SET
SAT
TEST / PAIRING
SELECT SET
SAT
TEST / PAIRING
SELECT SET
SAT
TEST / PAIRING
SELECT SET
SAT
TEST / PAIRING
SELECT SET
SAT
TEST / PAIRING
SELECT SET
SAT
TEST / PAIRING
SELECT SET
SAT
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
(the pairing process takes up to 9 minutes)
Press and hold TEST/PAIRING button
for 3 seconds.
3 sec
TEST / PAIRING
SELECT SET
THU
TEST / PAIRING
SELECT SET
TEST / PAIRING
SELECT SET
Once devices are successfully paired, LED on
the receiver will go solid red. Press and hold
TEST / PAIRING button for 3 seconds to end
the pairing process.
3 sec 3
TEST / PAIRING
SELECT SET
THU
TEST / PAIRING
SELECT SET
Press TEST / PAIRING button again to
return to the main screen.
ON
AUTO
OFF
MANUAL
1 sec
TEST / PAIRING
SELECT SET
THU
TEST / PAIRING
SELECT SET
THU
TEST / PAIRING
SELECT SET
THU
TEST / PAIRING
SELECT SET
THU
TEST / PAIRING
SELECT SET
THU
TEST / PAIRING
SELECT SET
THU
TEST / PAIRING
SELECT SET
THU
TEST / PAIRING
SELECT SET
THU
THU
Reset of the RT510TX+ thermostat
Remove the batteries without pressing any button.
Wait 2 minutes and insert the batteries again.
Your device will be restarted.
TEST / PAIRING
SELECT
+
+
SET
TEST / PAIRING
SELECT SET
SAT
When you want to change the batteries your
device will use the internal memory to backup
your settings. You have 30 seconds to change the
batteries before losing your settings.
NOTE:
If you do not notice the “low battery” symbol displayed on the screen in time, it will shut down. In
this case, after removing the old batteries, it is necessary to wait 5 minutes before inserting the new
batteries. Otherwise, it is possible that a condenser will remain partially discharged and it can prevent
the thermostat from restarting.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Salus RT510RF plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Salus RT510RF plus in the language / languages: English as an attachment in your email.

The manual is 12,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info