615593
37
Zoom out
Zoom in
Previous page
1/68
Next page
dEutScH
37
Nachdem die Achsen eingerichtet wurden, gehen Sie zum Kalibrierfenster (In FS2004
gehen Sie zu Empndlichkeiten). Wählen Sie die Ruderpedale aus und anschließend
„Advanced Controls“. Stellen Sie sicher, dass die Empndlichkeit für beide
Bremsachsen auf 75 % bis 80 % eingestellt ist und dass die Nullzonen für beide auf
0 % eingestellt sind. Das Ruder sollte auf eine Empndlichkeit von 50 % bis 75 % mit
einer geringen Nullzone von ungefähr 5 % eingestellt werden.
Bevor Sie einen Flug laden, müssen Sie das automatische Ruder deaktivieren.
Gehen Sie hierzu zu „Einstellungen“ > „Realismus“ und stellen Sie sicher, dass das
Kontrollkästchen „Autom. Ruder“ nicht markiert ist.
Jetzt können Sie starten. Laden Sie einen Flug und wenn das Flugzeug auf der
Startbahn steht, drücken Sie das Pedal nach unten und lassen sie es los. In der Ecke
des Bildschirms sollte eine Bremsmeldung angezeigt werden. Normalerweise wird
die Meldung wieder geschlossen, wenn die Bremse gelöst wird. Wenn die Bremsen
aktiviert bleiben, gehen Sie zu „Einstellung“ > „Steuerungen“ > „Kontrollachsen“ und
deaktivieren Sie das Kontrollkästchen „Umkehren“ für die Bremspedale.
auSFüHrEN dEr Smart tEcHNoLoGY proGrammING SoFtwarE
A. Klicken Sie auf Start und dann auf All Programs. Suchen Sie in der Programmliste
nach Smart Technology. Klicken sie auf dieses Programm. Es wird ein weiteres
Symbol namens Prole Editor angezeigt. Klicken Sie darauf. Smart Technology
Software wird geöffnet.
B. Gehen Sie auf Ihrem Desktop zum Smart Technology-Symbol. Doppelklicken Sie
darauf und die Smart Technology Software wird geladen.
C. Klicken Sie mit der rechten Maustaste auf das Controller-Symbol neben Ihrer Uhr
und anschließend in der Liste auf Prole Editor.
Wenn die ST-Software geöffnet ist, wird ein Hinweisbildschirm angezeigt (bei der ersten
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Saitek Pro Flight Cessna Yoke sYstem at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Saitek Pro Flight Cessna Yoke sYstem in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info