576476
18
Zoom out
Zoom in
Previous page
1/60
Next page
D380-D380A
USER GUIDE
1
Dear customer,
You have just acquired a new generation Sagemcom telephone and thank you for placing your
confidence in us.
This device has been manufactured with the utmost care. If you should have difficulties in operating
it, we recommend that you consult this user manual.
This product follows a strategy of continuous development. We reserve the right to make changes
without notice, modifications and improvements to the products described in this user manual.
To operate the device safely and easily, please read carefully the paragraphRecommendations
and safety instructions”, page 2.
The CE label confirms that the product complies with the 1999/5/EC regulations of the
European Union Parliament regarding wireless systems and telecommunications.
The declaration of compliance may be looked up on the www.sagemcom.com website
section «Support», or can be obtained from the following address :
Sagemcom Broadband SAS
250, route de l'Empereur
92848 Rueil-Malmaison Cedex - France
Copyright © Sagemcom Broadband SAS
All rights reserved
Sagemcom is a registered trademark.
2
Recommendations and
safety instructions
For safety reasons, never put the handset in the base station without the
battery inserted or without the lid on the battery compartment as this
could cause an electric shock.
To avoid damaging your handset/base, only use certified rechargeable
batteries NiMH 1.2 V 650 mAh, never use no rechargeable batteries.
Insert the batteries in the handset/base battery compartment respecting
polarity.
Only use the power unit supplied and connect it to the electricity mains in
accordance with the installation instructions in this user manual and the
details on the sticker regarding voltage, electrical current and frequency.
As a precaution if there is a risk of danger, the power plug can be pulled
out to disconnect the 230 volt power supply. Therefore the sockets should
be near the device and easily accessible.
Do not install your DECT telephone in a damp environment, such as a
bathroom, washroom, kitchen etc, and not within 1.50 metres of a source
of water or outside. This device is designed for use in temperatures of
between 5 °C and 45 °C.
In regions greatly affected by electrical storms we recommend that you
protect your telephone circuit with a special fixture for excess voltage.
Do not attempt to remove screws or open the appliance. It does not
contain any user-replaceable parts.
This device is designed to be used for connecting to the public telephone
network. If problems should arise, contact your nearest specialist dealer.
Only use the telephone cable supplied.
!
3
Your DECT telephone has a range of approx. 50 metres indoors and up
to 300 metres outdoors. The range can be affected by the proximity of
metal objects, such as a television and electrical devices.
Zones without reception may appear owing to elements in the building.
This can cause brief interruptions in the conversation, caused by faulty
transmission.
Certain medical equipment and highly-sensitive machines or security
systems may be affected by the transmission power of the telephone. In
these cases we recommend adhering to the safety information.
Your D380 has anti-skid pads that should leave no traces on your
furniture and ensure stability. However, given the the wide variety of
finishes used by furniture manufacturers, traces may appear on surfaces
in contact with the parts of your D380. Sagemcom Broadband SAS
decline all responsibility in any such cases of damage.
The used battery must be disposed of in line with the recycling
regulations in this user manual.
4
D380-D380A
Contents
Recommendations and safety instructions .........2
Discover.............................................................8
Your phone .......................................................................... 8
The base ................................................................................................................................................. 8
The handset ......................................................................................................................................... 10
The screen ........................................................................................................................................... 11
Handset set-up.................................................................... 12
Charging............................................................................. 13
Browsing through the menus............................................... 14
Browser................................................................................................................................................. 14
Programmable keys........................................................................................................................... 14
Illustration............................................................................................................................................. 15
Menu tree structure ........................................................................................................................... 17
Procedures in your booklet ............................................................................................................. 19
Making and receiving calls... ............................20
Managing a call ................................................................... 20
Making a call........................................................................................................................................ 20
Receiving a call .................................................................................................................................. 20
Managing several calls........................................................ 21
Receiving a second call ................................................................................................................... 21
Making a second call ........................................................................................................................ 21
Switching from one call to the other............................................................................................. 21
Ending one of the calls in progress .............................................................................................. 22
Talking with two contacts at the same time (3-party conference) ....................................... 22
Using additional handsets ................................................... 23
Calling another handset (intercom) .............................................................................................. 23
Transferring a call to another handset......................................................................................... 23
5
D380-D380A
Use the phonebook ............................................................. 24
Create an entry ................................................................................................................................... 24
Call the contact from their entry .................................................................................................... 24
Search for an entry ............................................................................................................................ 24
Changing an entry ............................................................................................................................. 24
Deleting an entry ................................................................................................................................ 25
Associating a ring tone with an entry........................................................................................... 25
Adding another number to an entry.............................................................................................. 25
Transferring entries from one handset to another.................................................................... 26
Options during a call ........................................................... 27
Enable/Disable loudspeaker (handsfree mode)........................................................................ 27
Adjusting the volume......................................................................................................................... 28
Enabling/Disabling the secret mode ............................................................................................ 28
Locating your handset ........................................................ 29
Listening and Recording... (model D380A)......30
Enabling/disabling the answering machine.......................... 30
Answering machine announcements................................... 30
Saving your personal announcement........................................................................................... 31
Listening to your announcement ................................................................................................... 31
Erasing your announcement........................................................................................................... 31
Messages............................................................................ 32
Listening to your messages ............................................................................................................ 32
Managing your messages................................................................................................................ 33
Querying your answering machine remotely ............................................................................. 34
Delete all your messages................................................................................................................. 35
Recording a conversation ............................................................................................................... 35
Answering machine settings ............................................... 36
Changing the remote querying code ........................................................................................... 36
Changing the recording quality ..................................................................................................... 36
Changing the number of rings ....................................................................................................... 36
6
D380-D380A
Setting up.........................................................37
The phone........................................................................... 37
Changing the ringing tone............................................................................................................... 37
Enabling/Disabling audio alerts ..................................................................................................... 37
Enabling/Disabling the silent mode .............................................................................................. 37
Defining programmable key shortcuts......................................................................................... 38
Setting the date and the time.......................................................................................................... 38
Picking up and hanging up calls automatically......................................................................... 38
Changing your voice mail number ................................................................................................ 39
Checking your operator voice mail............................................................................................... 39
Changing the display language..................................................................................................... 39
Enabling/Disabling keyboard locking .......................................................................................... 40
Defining banned calls (Parental Control).................................................................................... 40
Changing the default code.............................................................................................................. 41
Allow/Prevent the sharing of a call with another handset ...................................................... 41
The handset ........................................................................ 41
Associating a new handset ............................................................................................................. 41
Define the priority base for a handset.......................................................................................... 42
Resetting the handset....................................................................................................................... 42
Customizing the handset’s registration ....................................................................................... 43
Renaming the handset...................................................................................................................... 43
Adjusting the contrast....................................................................................................................... 43
The base ............................................................................. 44
Enabling the paging mode .............................................................................................................. 44
Adjusting the volume of the messages heard from the base................................................ 44
Resetting the base............................................................................................................................. 45
Removing a handset registered on the base ............................................................................. 45
Renaming the base............................................................................................................................ 45
The line ............................................................................... 46
Changing the network type ............................................................................................................. 46
Changing the dialling type .............................................................................................................. 46
Changing the flash duration............................................................................................................ 46
Defining the outside call prefix (PABX)........................................................................................ 47
Modifying the country ....................................................................................................................... 47
7
D380-D380A
Enjoy................................................................48
The alarm............................................................................ 48
Programming the alarm.................................................................................................................... 48
Finding out the alarm status............................................................................................................ 48
Enabling/Disabling the alarm.......................................................................................................... 49
Changing the ringing tone............................................................................................................... 49
Defining the wake-up time............................................................................................................... 49
The Surveillance mode........................................................ 50
Enabling the surveillance mode..................................................................................................... 50
Disabling the surveillance mode ................................................................................................... 50
Tracing your calls.............................................51
Call logs.............................................................................. 51
Viewing the received and dialled call log ................................................................................... 51
Managing incoming or outgoing calls.......................................................................................... 51
The events log..................................................................... 52
Checking new events........................................................................................................................ 52
Enabling/Disabling event notification........................................................................................... 52
Environnement .................................................53
Packaging........................................................................... 53
Batteries ............................................................................. 53
The product ........................................................................ 53
Guarantee ........................................................54
Lexicon ............................................................58
8
D380-D380A
Your phone
The base
Model without answering machine (D380)
Discover...
Caption Description
1 Handset location
2
button Paging/Pairing:
Short press
: paging of handsets.
Long press
: pairing of handsets
1
D380
1
2
9
D380-D380A
Model with answering machine (D380A)
Key Description Key Description
1 Handset location. 4 Display:
Answering machine off
: no
display.
Answering machine enabled
:
- No new messages: a dash
is displayed.
- New messages have been
received: the unread
messages counter flashes
and displays the number of
messages received
(up to 9).
2
Short press
: read / stop
reading messages
3 Message deletion:
Long press in read mode
:
delete a message.
Long press when not in read
mode
: delete already read
messages.
5 Paging button:
Short press
: paging of
handsets.
Long press
: pairing of
handsets
D380A
2
1
3
4
5
10
D380-D380A
The handset
Key Description Key Description
1 Speaker. 9 Microphone.
2 Graphic screen. 10Star key / Keypad lock
3 Programmable/cancel
shortcut key.
11 Long press:
If the answering machine is
turned off: access to voice
mail.
If the answering machine is
turned on: access to your
messages on the answering
machine.
4 Browsing through the
menus.
12 Speakerphone key.
5 Hang up key 13 Pick-up / Hands-free /
Redial (long press) key
11
D380-D380A
The screen
THE ICONS DISPLAYED
In standby mode or during use, your phone screen informs you of your phone’s current
state through icons, and in particular:
6 Phonebook access key. 14 Programmable/confirm
shortcut key.
7 Alphanumeric keyboard. 15 Loudspeaker in
speakerphone mode.
8 # key
Caption Description
1Status icons
Indicates your phone’s current state.
Battery charge condition Network
Phone in conversation mode Alarm on
Secret mode on
Only for the D380A model
Speakerphone on Answering machine enabled
- steadily displayed: answering
machine on
- flashing: new message
- Answering machine off: no
display
Low transmission
Key Description Key Description
Calls
TAM
2
1
3
12
D380-D380A
LOW TRANSMISSION MODE
Your handset has a Low transmission mode It manages the radio transmission power
required according to how far you are away from your base.
Handset set-up
1 Take the batteries and the hatch provided in the
packaging.
2 Turn over your handset and press the top of the
hatch to release it.
3 Insert the batteries one by one according to their
polarities as indicated in the illustration opposite.
4 Fit the hatch to the handset by pushing it up until it
is completely closed.
5 The screen turns on. Place your handset on its
base and fully charge the batteries.
6 A beep sounds when you place the handset on the
base.
The battery charging icon moves to inform you that
charging is in progress. The icon display stops
moving when the batteries are charged.
2 Information field
handset placed on the base
: the current time is displayed,
handset off-hook
: the handset number, the date and the time are
displayed.
3 Action icons
handset placed on the base
: browser actions and the confirm key,
handset off-hook
: menus associated with programmable keys.
Caption Description
13
D380-D380A
Charging
To charge your phone, place the handset on the base, making sure that the base is
connected to an AC outlet.
The battery charging icon moves to inform you that charging is in progress. The icon
display stops moving when the batteries are charged.
BATTERY REPLACEMENT
1 Turn off the handset. Turn it over to access the battery compartment hatch.
2 Remove the battery compartment hatch.
3 Remove the old batteries, insert the new batteries one by one the right way as
indicated by their polarities.
4 Refit the battery compartment hatch.
Notes To ensure optimum charging, leave the handset on the base for at
least 15 hours when using the phone for the first time. During
charging, the batteries may heat up. This is quite normal and perfectly
safe.
If you do not obtain radio contact with your base, check the electrical
connections to your base.
Notes Worn out batteries should be discarded in accordance with the
recycling instructions given in chapter “Recommendations and safety
instructions”, page 2.
CAUTION To prevent damage to your handset, only use approved AAA
format NiMH 1.2 V 650 mAh rechargeable type batteries. Never
use No-rechargeable batteries.
14
D380-D380A
Browsing through the menus
Browser
This browser allows you to quickly access menus and change your
settings easily. It points in two directions.
When choosing menus, press the top or the bottom of the browser
to access the previous or next menu.
During a call, press the top of the browser to increase the volume or
the bottom to decrease it.
Programmable keys
Your phone has two so-called “programmable” keys allowing you to associate a shortcut
to the menu you use most. This shortcut can then be accessed from the your phone’s
home screen.
These keys are also used to confirm or cancel an action in a menu.
Programmable
key...
Use this key from the home
screen to...
Use this key from the
menus to...
Left
Directly access the associated
menu through the shortcut.
Confirm the current entry.
Display context-sensitive
menu options during a call.
Display options during a call
Right
Cancel the current entry.
Notes For further details on programming the left and right programmable
keys, see section “Defining programmable key shortcuts”, page 38.
15
D380-D380A
Illustration
To browse through menus, use the browser and the two programmable keys:
DETAILED BROWSER EXAMPLE: ADJUST THE DATE AND TIME
To access the date and time setting menu:
1 Press the top or bottom of the browser key .
The main menu is displayed on the screen.
1 Press the top or bottom of the browser key .
The main menu is displayed on the screen.
2 Press the top or bottom of the browser key to scroll through the menus
and access the desired function.
3 Confirm your choice/Enter the displayed menu by pressing the left
programmable key .
4 Cancel your choice/Exit the displayed menu:
- either by pressing the right programmable key ,
- or by pressing the key; the home screen is displayed.
Notes It is recommended to set the date and time accurately to allow you to
follow the chronological order of your calls and messages.
Notes If you have the Display number option, the date and time will,
depending on your operator, be set automatically when you receive a
call.
16
D380-D380A
2 Scroll through the menus to the SETTINGS menu by pressing the top or bottom
of the browser key .
3 Enter the SETTINGS menu by pressing the left programmable key .
The SETTINGS menu is displayed.
4 Scroll through the menus to the DATE/TIME menu by pressing the top or bottom
of the browser key .
5 Enter the DATE/TIME menu by pressing the left programmable key .
The DATE/TIME menu is displayed.
6 Enter the DATE: using the numeric keypad (day, month and year) in the form
DD/MM/YY.
7 Confirm your entry by pressing the left programmable key .
The home screen displays the message OK.
8 Enter the TIME: using the numeric keypad (hours then minutes).
9 Confirm your entry by pressing the left programmable key .
The home screen displays the message OK.
You have just set your phone’s current date and time.
Refer to the “Menu tree structure”, page 17 section to find out about your phone’s
functions.
17
D380-D380A
Menu tree structure
PHONEBOOK
CALLS
ACCESSORIES
RINGER TONE
Option
< New >
VIEW
CALL
EDIT
SEARCH
RING TONE
ADD NUMBER
NEW ENTRY
DELETE
TRANSMIT
INCOMING CALLS
OUTGOING CALLS
EVENTS
ALARM
ROOM MONITOR.
EXTERNAL CALL
INTERNAL CALL
BEEPS
SILENT MODE
Contextual menu
HANDSFREE
LOUDSPEAK BASE (*)
CALL TRANSFER (**)
SECOND CALL
PHONEBOOK
CALLS
SECRET
RECORD
In conversation mode
(*) Only for the D380A model.
(**) Only if two handsets are registered on the same base.
SWITCH
3-PARTY CONF
HANDSFREE
LOUDSPEAK BASE (*)
PHONEBOOK
CALLS
SECRET
RECORD (*)
HANGING UP
SECOND CALL
FIRST CALL
18
D380-D380A
SETTINGS
PROGRAM KEYS
DATE/TIME
CONTRAST
AUTO HANG UP
AUTO PICKUP
VOICE BOX No
LANGUAGE
KEYPAD LOCK
RESTRICTION
ADVANCED SET.
SET HANDSET REGISTRATION
BASE PRIORITY
RESET HANDSET
PERSON.REGISTR
HANDSET NAME
REGISTR.MODE
RESET BASE
DELETE HANDSET
RENAME BASE
INTRUSION
SET BASE
SET LINE
NETWORK TYPE
DIAL
FLASHING
PABX PREFIX
COUNTRY
CHANGE CODE
19
D380-D380A
Procedures in your booklet
The procedures in your booklet are presented in the form of sheets.
To facilitate their implementation, each of them includes the following as appropriate:
the keys associated to directly access the function described, and/or
the path for accessing the function described in the menu.
EXAMPLE:
ANS.MACH. (*)
MESSAGES
(*) Only for the D380A model.
PLAY
DELETE OLD
PLAY
CHANGE
DELETE
CALL SCREENING
REMOTE CODE
MODE ENREG.
NO OF RINGS
SPK.BS LEVEL
ANSWERING MODE
OUTGOING MSG.
SETTINGS
> HANDSFREE means that you access this function by
displaying the menu and then the
HANDSFREE function. > HANDSFREE
means that you access this function by
displaying the menu and then the
HANDSFREE function.
Contextual menu> HANDSFREE means that you access this function by
displaying the menu and then the
HANDSFREE function.
20
D380-D380A
Managing a call
Making and
receiving calls...
2
Making a call
METHOD 1
1 Dial your contact’s number.
2 Press the key .
METHOD 2
1 Press the key .
2 Dial the number.
A beep sounds.
At the end of the call, press the handset key and replace the handset on its
base.
1 2
1
2
Receiving a call
1 Press the key to take the call.
2 At the end of the call, press the
handset key and replace the
handset on its base.
A beep sounds.
1 2
Notes Your handset includes the AUTO PICKUP and AUTO HANG UP
functions.
For further details, refer to the “Picking up and hanging up calls
automatically”, page 38 section.
21
D380-D380A
Managing several calls
Your phone allows you to take and manage several calls when you are already on the
line.
These calls can be managed with the Contextual menu.
Receiving a second call
During a call, a beep indicates the arrival of a second call.
To take this call, press ACCEPT when the message is displayed on the screen.
Your first call is put on hold and you can talk with the second caller.
Making a second call
Dial your contact’s number and confirm.
The message SECOND CALL is displayed on the screen to indicate that the second
call is in progress.
Contextual menu > SECOND CALL
Switching from one call to the other
The call in progress is then put on hold and you can take back the previous call.
Contextual menu > SWITCH
22
D380-D380A
Ending one of the calls in progress
The call in progress is interrupted and you take back the previous call.
Contextual menu > HANGING UP
Talking with two contacts at the same time
(3-party conference)
You can then talk with your two contacts at the same time.
To end the 3-party conference, press the key .
Contextual menu > 3-PARTY CONF
23
D380-D380A
Using additional handsets
You can associate additional handsets with your phone: You can then make and receive
outside calls or calls between these handsets.
Notes You first have to pair the handsets with the base.
For further details, refer to the “Associating a new handset”, page 41
section.
Calling another handset (intercom)
1 Enter the handset’s number directly on the keyboard.
2 Press Call.
The selected handset rings.
3 Take the call from the handset by pressing .
4 End the call by pressing .
Transferring a call to another handset
1 Select the handset and confirm.
The handset called rings.
2 Pick up the other handset and then transfer the call by pressing .
Contextual menu > CALL TRANSFER
Notes You must have at least two handsets paired on the same base.
24
D380-D380A
Use the phonebook
Create an entry
Specify the required information by confirming at each step:
NEW NAME? : enter your contact’s name,
NEW NUMBER? : enter their number,
HOME, WORK, MOBILE or FAX : select the number type.
Menu > PHONEBOOK > < New >
Call the contact from their entry
Confirm or press the key or the speakerphone key directly.
Menu > PHONEBOOK > Option > CALL
Search for an entry
Enter the first letter of the name and confirm.
When your handset is in standby mode, hold down the key (long press)
corresponding on the first letter of the name to be looked up.
Menu > PHONEBOOK > Option > SEARCH
Changing an entry
Change the name and/or number and/or number type and confirm.
Menu > PHONEBOOK > Option > EDIT
25
D380-D380A
Deleting an entry
Confirm the deletion of the entry.
Menu > PHONEBOOK > Option > DELETE
Associating a ring tone with an entry
Scroll down the list of available ring tones and confirm.
Menu > PHONEBOOK > Option > RING TONE
Adding another number to an entry
Specify the required information by confirming at each step:
NEW NUMBER? : enter their number,
HOME, WORK, MOBILE or FAX : select the number type.
Menu > PHONEBOOK > Option > ADD NUMBER
26
D380-D380A
Transferring entries from one handset to
another
Each handset has its own phonebook.
To transfer one or more entries from a phonebook to another handset:
1 Confirm the message BY INTERCOM.
2 Choose the desired option to transfer:
- ONE ENTRY : the current entry,
- MANY ENTRIES : the selected entries,
- ALL ENTRIES : all the phonebook entries.
3 Select the handset to which the data are to be transferred.
The receiving handset rings.
4 Pick up the handset by pressing .
A confirmation message is displayed.
5 The transfer takes place.
Menu > PHONEBOOK > Option > TRANSMIT
Notes You must have at least two handsets paired on the same base.
27
D380-D380A
Options during a call
You can use the following options during a call:
Enable/Disable loudspeaker (handsfree mode)
HANDSET LOUDSPEAKER
BASE LOUDSPEAKER (D380V ONLY)
A confirmation screen is displayed.
or (during a call)
Or
Contextual menu > HANDSFREE > ACTIV. or Deact.
Contextual menu > LOUDSPEAK BASE > ACTIV. or Deact.
Or
Notes When your battery charging icon displays the minimum, the
handsfree mode is unavailable until the next charging cycle.
28
D380-D380A
Adjusting the volume
To increase the volume, press .
To decrease the volume, press .
Enabling/Disabling the secret mode
Or
The secret mode allows you to temporarily mute the line so that you are not heard
by the caller. Once enabled, the SECRET MODE message flashes on the screen.
(during a call)
Contextual menu > SECRET > ACTIV. or DISABLE
29
D380-D380A
Locating your handset
If you have misplaced your handset, press the key on your phone’s base. The
handset rings.
30
D380-D380A
Answering machine announcements
Listening and
Recording...
(model D380A)
3
IMPORTANT When you answering machine’s memory is full, the answering
machine turns off. You have to read your messages and delete
some to free up memory space.
Enabling/disabling the answering
machine
When the answering machine is enabled, the icon is displayed on the screen.
Menu > ANS.MACH. > ANSWERING MODE > ACTIVATED or OFF
Notes For further details on the settings of your answering machine, see
section “Setting up...”, page 37.
Notes If you have not saved a personal announcement, the answering
machine will automatically use the pre-recorded announcement.
31
D380-D380A
Saving your personal announcement
Confirm the instructions on the screen.
Menu > ANS.MACH. > OUTGOING MSG. > CHANGE
Listening to your announcement
The current announcement used is played.
Menu > ANS.MACH. > OUTGOING MSG. > PLAY
Erasing your announcement
Confirm the instructions on the screen.
Menu > ANS.MACH. > OUTGOING MSG. > DELETE
Notes If you have erased your personal announcement, the answering
machine will use the pre-recorded announcement.
32
D380-D380A
Messages
Listening to your messages
FROM THE BASE
FROM THE HANDSET
The messages are read in chronological order (from oldest to newest).
At the end of the last message, the answering machine will stop automatically.
Menu > ANS.MACH. > MESSAGES > PLAY
Notes For better listening comfort, see section “Adjusting the volume of
the messages heard from the base”, page 44.
Notes Depending on your operator and your subscription, your
contact’s name and number are displayed on the screen.
33
D380-D380A
Managing your messages
When playing back messages, press the following buttons:
TO... FROM THE BASE FROM THE HANDSET
Go on to the next message
1 press
Return to the start of the
message
1 press
Return to the previous message
2 presses
Pause/Resume reading
1 press
Stop/Start message again
1 short press
Delete the message being read
1 long press 1 press
34
D380-D380A
Querying your answering machine remotely
This function allows you to check your messages from outside.
When playing back messages, press the following buttons:
1 Dial your phone number and wait for 12 rings before the remote querying
function cuts in.
2 While listening to your announcement, press the key and enter your remote
querying code.
TO... FROM THE BASE
Read messages
1 press
Enable the answering/recording machine
1 press
Disable the answering/recording machine
1 press
Go on to the next message
1 press
Return to the start of the message
1 press
Return to the previous message
2 presses
Delete the message being read
1 press
Pause/Continue playing back
1 press
Notes The default code is 0000. You can change it.
For further details, refer to paragraph “Changing the remote
querying code”, page 36.
35
D380-D380A
Delete all your messages
FROM THE BASE
FROM THE HANDSET
Confirm the deletion.
(1 long press) only for messages already read.
Menu > ANS.MACH. > MESSAGES > DELETE OLD
Recording a conversation
Confirm the messages on the screen.
Contextual menu > RECORD > Begin then End.
CAUTION The Penal Code prohibits the recording of a conversation
without your contact’s knowledge. You have to obtain your
contact’s authorization before using this function.
36
D380-D380A
Answering machine settings
Enabling/Disabling call filtering
Call filtering allows you to take only the calls you want.
Other calls will be recorded on the answering machine.
Menu > ANS.MACH. > SETTINGS > CALL SCREENING > ON or OFF
Changing the remote querying code
You can give this code to anyone who needs to check their messages outside.
Follow the instructions on the screen to change the code.
Menu > ANS.MACH. > SETTINGS > REMOTE CODE > MODIFY CODE?
Notes The default code is 0000.
Changing the recording quality
Two quality modes are available:
HIGH for higher quality (12 minutes and 30 seconds of recording),
STD for standard quality (24 minutes).
Menu > ANS.MACH. > SETTINGS > MODE ENREG. > HIGH or STD
Changing the number of rings
You can increase the number of rings before the answering machine cuts in to give
yourself longer to take the call.
Select the number of rings you want (up to 7 rings).
Menu > ANS.MACH. > SETTINGS > NO OF RINGS > 2 to 7
37
D380-D380A
The phone
Setting up...
4
Changing the ringing tone
You can change the ringing tone of:
outside calls,
calls between handsets (intercom).
Scroll through the pre-recorded ring tones and confirm.
Menu > RINGER TONE > EXTERNAL CALL and INTERNAL CALL
Enabling/Disabling audio alerts
The audio alerts apply to:
low battery,
keyboard keys pressed,
placing the handset on the base.
Follow the instructions on the screen and confirm.
Menu > RINGER TONE > BEEPS > KEYTONE and CHARGER and BATTERY LOW
Enabling/Disabling the silent mode
Follow the instructions on the screen and confirm.
A direct-access key can also be configured with this function.
Menu > RINGER TONE > SILENT MODE
38
D380-D380A
Defining programmable key shortcuts
You can define a shortcut for the function(s) you use most.
Select the menu to be displayed as a shortcut for the left and right
programmable keys, confirming each step.
Menu > SETTINGS > PROGRAM KEYS
Setting the date and the time
1 Enter the DATE: in as DD/MM/YY.
2 Enter the TIME: starting with the hours and then the minutes.
3 Confirm your entry.
For further details, refer to the “Illustration”, page 15 section.
Menu > SETTINGS > DATE/TIME
Picking up and hanging up calls automatically
This function allows you to take and end a call by simply taking the handset off its
base or placing it back on its base.
Follow the instructions on the screen and confirm.
Menu > SETTINGS > AUTO HANG UP and AUTO PICKUP
39
D380-D380A
Changing your voice mail number
Enter the voice mail number and confirm.
There are two ways of recording messages:
Answering machine enabled: the messages are recorded on your D380A’s
internal answering machine.
Answering machine disabled: messages are handled by your operator voice
mail.
Menu > SETTINGS > VOICE BOX No
Notes If you do not know your voice mail number, request it from your
operator.
Notes For further details on your operator voice mail, refer to
section “Checking your operator voice mail”, page 39
Checking your operator voice mail
Follow the instructions issued by your operator’s online answering machine.
(long press)
Notes You must first define the phone number for your operator voice
mail.
Changing the display language
Select the language to be used and confirm.
Menu > SETTINGS > LANGUAGE
40
D380-D380A
Enabling/Disabling keyboard locking
This function allows you to lock the keyboard when you are not on line.
FROM THE HANDSET
Follow the instructions on the screen and confirm.
(1 long press)
Menu > SETTINGS > KEYPAD LOCK
Notes To unlock the keyboard, make a long press on .
Defining banned calls (Parental Control)
You can inhibit calls to numbers with surcharged prefixes or international calls, for
example, by defining up to 5 profiles.
1 Enter the base code and confirm.
2 Select an entry (from 0 to 4) and confirm.
3 Enter the prefix to be inhibited and confirm.
Menu > SETTINGS > RESTRICTION
Notes The default code is 0000.
41
D380-D380A
The handset
Changing the default code
Enter the old and then the new code and confirm.
Menu > SETTINGS > ADVANCED SET. > CHANGE CODE
Allow/Prevent the sharing of a call with another
handset
Follow the instructions on the screen and confirm.
Menu > SETTINGS > ADVANCED SET. > SET BASE > INTRUSION
Notes If you disable the intrusion mode, you will not be able to share a
call in process with another handset.
Associating a new handset
Your phone allows you to associate other handsets with the base. You then have to
page/pair them so that they are recognized.
FROM THE HANDSET:
1 Enable the function.
FROM THE BASE:
2 Enabling the paging mode.
Refer to section “Enabling the paging mode”, page 44.
Once the handset is registered, the paging mode is automatically exited.
Menu > SETTINGS > ADVANCED SET. > SET HANDSET > REGISTRATION
42
D380-D380A
Define the priority base for a handset
This function allows you to specify the priority base to be used for making calls.
Select the base that the handset should use first.
Menu > SETTINGS > ADVANCED SET. > SET HANDSET > BASE PRIORITY
Notes Only if you have paged/paired the same handset on several
bases.
Notes The automatic mode avoids you having to specify a priority.
Resetting the handset
When you reset your handset, all the settings are returned to their initial values
(factory settings), except for the phonebook.
Follow the instructions on the screen and confirm.
Menu > SETTINGS > ADVANCED SET. > SET HANDSET > RESET HANDSET
43
D380-D380A
Customizing the handsets registration
You can customize the following information:
your base’s name,
the handset’s registration number.
FROM THE HANDSET:
1 Select the base number and confirm.
2 Enter the new base name and confirm.
3 Enter the base code.
FROM THE BASE:
4 Press the paging button for several seconds .
On the D380 base: the green light flashes, meaning that the base is in paging
mode.
On the D380A base: a dash flashes on the display, meaning that the base is in
paging mode.
Once the handset is registered, the paging mode is automatically exited.
Menu > SETTINGS > ADVANCED SET. > SET HANDSET > PERSON.REGISTR
Notes The default code is 0000.
Renaming the handset
You can assign a meaningful name to your handset if you have several handsets
Follow the instructions on the screen and confirm.
Menu > SETTINGS > ADVANCED SET. > SET HANDSET > HANDSET NAME
Adjusting the contrast
Select the LEVEL 1, the LEVEL 2 or LEVEL 3 and confirm.
Menu > SETTINGS > CONTRAST
44
D380-D380A
The base
Enabling the paging mode
You enable the paging mode when you associate an additional handset, for
example.
Or
The green indicator light flashes: the base is in paging mode.
Menu > SETTINGS > ADVANCED SET. > SET BASE > REGISTR.MODE
Notes Your base will remain in paging mode for about a minute.
Adjusting the volume of the messages heard
from the base
For better listening comfort, you can adjust the volume when listening to answering
machine messages from the base.
Select the desired level (LOW, MEDIUM or HIGH) and confirm.
Menu > ANS.MACH. >SETTINGS >SPK.BS LEVEL
45
D380-D380A
Resetting the base
When you reset your base, all the settings are returned to their initial values (factory
settings), except for the phonebook.
Follow the instructions on the screen and confirm.
Menu > SETTINGS > ADVANCED SET. > SET BASE > RESET BASE
Removing a handset registered on the base
1 Enter the base code and confirm.
2 Select the handset number and confirm.
Menu > SETTINGS > ADVANCED SET. > SET BASE > DELETE HANDSET
Notes The default code is 0000.
Renaming the base
You can assign a meaningful name to your base if you have several bases.
Follow the instructions on the screen and confirm.
Menu > SETTINGS > ADVANCED SET. > SET BASE > RENAME BASE
46
D380-D380A
The line
Important We do not recommend that you change line settings without first
contacting your operator, as this may result in your phone line being
disconnected.
Changing the network type
You can connect your phone to a public or private network.
Follow the instructions on the screen and confirm.
Menu > SETTINGS > ADVANCED SET. > SET LINE > NETWORK TYPE >
PRIVATE or PUBLIC
Changing the dialling type
You can use a voice frequency or pulse based dialling system.
Follow the instructions on the screen and confirm.
Menu > SETTINGS > ADVANCED SET. > SET LINE > DIAL > TONE or PULSE
Changing the flash duration
You can configure the flash duration if you use your phone abroad or on a private
network.
For further details, refer to section “
Changing the network type”, page 46
.
.
Follow the instructions on the screen and confirm.
Menu > SETTINGS > ADVANCED SET. > SET LINE > FLASHING > 80 MS to 600 MS
47
D380-D380A
Defining the outside call prefix (PABX)
You can define the outside call prefix if you use your phone on a private automatic
branch exchange.
For further details, refer to the “Lexicon”, page 58 section .
The following options are available:
ACTIVATE / DEACTIVATE : to define the prefix status.
PREFIX : to enter the number that allows you to access the outside line.
EDIT LENGTH : to specify the length of the number before automatic dialling of
the prefix (from 01 to 99).
Menu > SETTINGS > ADVANCED SET. > SET LINE > PABX PREFIX > ACTIVATE /
DEACTIVATE or PREFIX or EDIT LENGTH
Modifying the country
Tihs menu allows you to select the country where you are
using the telephone.
Follow the instructions on the screen and confirm.
Menu > SETTINGS > ADVANCED SET. > SET LINE > COUNTRY
48
D380-D380A
The alarm
Enjoy...
5
Notes The alarm sounds for 60 seconds through the handset speaker.
To stop the alarm clock, press any key on the handset.
Programming the alarm
To program the alarm:
1 Depending on the alarm status, enable or disable the ALARM function.
2 If necessary, change the ring tone.
3 Select the time at which you want to be woken up.
For further details, refer to the following sections.
Menu > ACCESSORIES > ALARM
Finding out the alarm status
The display indicates the alarm status (ALARM CLOCK OFF or the alarm time
programmed).
Confirm to save the indicated information or display the options by pressing .
Menu > ACCESSORIES > ALARM
49
D380-D380A
Enabling/Disabling the alarm
Follow the instructions on the screen and confirm.
Once the alarm is enabled, the icon is displayed on the screen.
Menu > ACCESSORIES > ALARM > ACTIVATE or DEACTIVATE
Changing the ringing tone
Scroll down the list of available ring tones and confirm.
Menu > ACCESSORIES > ALARM > RINGER TONE
Defining the wake-up time
Follow the instructions on the screen and confirm.
Menu > ACCESSORIES > ALARM > SET TIME
50
D380-D380A
The Surveillance mode
This function allows you to monitor a room, by placing the first handset (transmitter) in
the room to be monitored, and the second handset (receiver) near you.
Notes You must have at least two handsets registered on the same base to
use this mode.
Enabling the surveillance mode
ON THE RECEIVING HANDSET:
1 Select the calling handset to be called.
The handset rings.
ON THE CALLING HANDSET:
2 Pick up the second handset by pressing .
3 Confirm the transition to surveillance mode.
Menu > ACCESSORIES > ROOM MONITOR.
Notes In calling mode, the phone will not ring if a call comes in.
You can still make or take a call from the receiving handset,
however.
Disabling the surveillance mode
Press Off on the receiving and calling handsets.
51
D380-D380A
Call logs
Logs are lists of numbers or events received by your phone.
Depending on your operator, call logs contain the following information:
your contact’s name or number,
the call time or date.
Tracing your calls...
6
Viewing the received and dialled call log
Scroll through the list of stored numbers.
You can use the options described in section “Managing incoming or outgoing
calls”, page 51.
A shortcut is set as default for the key to access the log directly.
Menu > CALLS > INCOMING CALLS or OUTGOING CALLS
Managing incoming or outgoing calls
Use the following options from the call list to:
VIEW : display the information about the selected call,
CALL : call the displayed number,
DELETE : delete the stored number,
STORE NUMBER : save the number in your phonebook,
DELETE ALL : delete all the numbers in the list.
Menu > CALLS > INCOMING CALLS or OUTGOING CALLS > Option
52
D380-D380A
The events log
The NEW EVENT! message informs you that you missed a call or message.
Checking new events
Or
Select the event and confirm.
NEW EVENT! +
Menu > CALLS > EVENTS > VIEW
NEW EVENT!
Enabling/Disabling event notification
Disable this function to delete the display of the NEW EVENT! message.
Menu > CALLS > EVENTS > ACTIVATE or DEACTIVATE
53
D380-D380A
Environnement
Environmental protection and sustainable development is an important priority for
Sagemcom. Sagemcom has a policy of using environmentally- friendly systems and
makes environmental protection an essential part of the life-cycle of its products – from
the manufacturing, to the installation, operation and disposal.
Packaging
The logo (green point) on the packaging means that a fee is paid to an
authorised national organisation to improve packaging recycling and the
recycling infrastructure. Follow the local sorting regulations for this type of
waste product in order to improve recycling.
Batteries
If your product contains batteries, they must be disposed of at the designated collection
points.
The product
The crossed out dustbin displayed on the product signifies that it belongs
to the electrical and electronic equipment group. The European regulations
request you to carry out your own selective recycling collection at:
the sales outlet when you buy a similar new device.
the collection points available in your area (recycling centres, sorting points, etc).
This means you participate in the recycling and valorisation of used electric and
electronic goods which would otherwise have a negative impact on the environment and
health.
54
D380-D380A
Guarantee
Terms and Conditions for United
Kingdom & Ireland only
In order to apply the guarantee, you should contact the Sagemcom Helpdesk or the
retailer where you purchased the equipment. Proof of purchase will be required in either
case.
Please make sure that you use your equipment only for the purpose for which it was
designed and under normal usage conditions.
Sagemcom do not accept any liability for the equipment if used outside the frame of its
original designed purpose or any consequence that may arise from this usage.
Should any malfunction arise, the Sagemcom Helpdesk or your retailer will advise you
how to proceed.
A) General Guarantee conditions
Sagemcom undertakes to remedy by repair or exchange at its own convenience, free of
charge for labour and replacement parts, any defects in the equipment during the
guarantee period of 12 (twelve) months or 3 (three) months for accessories, from the date
of original invoice of the Equipment, where those defects are a result of faulty
workmanship.
Unless the customer has concluded with Sagemcom a maintenance contract in respect
of the equipment which specifically provides for repairs to be carried out at the
customer`s premises, the repairs will not be carried out on the equipment at the customer
premises.
The customer must however return the defective equipment at his/her own expense, to
the address supplied by the Sagemcom Helpdesk or by the retailer.
In the case that a product needs to be sent in for a repair, it must always be accompanied
by a proof of purchase (which is not altered, written on or in any way made illegible)
showing that the product is still under guarantee. In the case that no proof of purchase
is enclosed, the Sagemcom repair centre will use the production date as its reference for
establishing the guarantee status of the product.
Apart from all legal obligatory rules, Sagemcom, do not give any Guarantee, either
implicit or explicit which is not set force in the present section, and can not be held
responsible for any direct or indirect, material or immaterial damage, either in or out of
the frame of the present guarantee.
55
D380-D380A
If any provision of this guarantee shall be held to be in whole or in part invalid or illegal
due to an obligatory rule applicable to consumers pursuant to their national legislation,
such invalidity or illegality shall not impair or affect the remaining provisions or parts of
this guarantee.
This guarantee does not affect the Customer statutory rights
B) General Guarantee conditions
Sagemcom shall have no liability under the guarantee in respect of:
Damage, defects, breakdown or malfunction due to one or more of the following:
- Failure to properly follow the installation process and instructions for use
- An external cause to the equipment (including but not limited to: lightening, fire,
shock, vandalism, inappropriate conditions of electrical network or water damage
of any nature)
- Modifications made without the written approval of Sagemcom
- Unsuitable operating conditions, particularly of temperature and humidity
- Repair or maintenance of the equipment by persons not authorised by Sagemcom
Wear and tear from normal daily use of the equipment and its accessories
Damage due to insufficient or bad packaging of equipment when returned to
Sagemcom
Usage of new versions of software without the previous approval of Sagemcom
Work on any equipment or software modified or added without the prior written
consent of Sagemcom
Malfunctions not resulting from the Equipment or from software installed in user
workstations for the purpose of use of the equipment.
Communication problems related to an unsuitable environment including:
- Problems related to access and/or connection to the Internet such as interruptions
by access networks or malfunction of the line used by the subscriber or his
correspondent
- Transmission faults (for example poor geographical coverage by radio and TV
transmitters, interference or poor line quality)
- Local network faults (wiring, servers, workstations) or the failure of the transmission
network (such as but not limited to interferences, fault or poor quality of the
network)
- Modification of the parameters of the cellular or broadcast network carried out after
the sale of the Product
Normal servicing (as defined in the user guide supplied with the equipment) as well
as malfunctioning due to servicing not being carried out. Servicing costs are in any
event always borne by the customer.
Malfunctions resulting from the usage of products, consumables or accessories not
compatible with the equipment.
56
D380-D380A
C) Out of Guarantee Repairs
In the cases set forth in B) as well as after expiry of the guarantee period, the customer
must ask the Authorised Sagemcom Repair Centre for a cost estimation prior to work
being carried out. In such cases, the repair and delivery costs will be invoiced to the
customer.
The foregoing shall apply unless otherwise agreed in writing with the customer and only
for the United Kingdom and Ireland.
www.sagemcom.com
57
D380-D380A
TERMS AND CONDITIONS FOR OTHER
COUNTRIES
If, despite our best efforts, your product presents any defects, you should refer to your
retailer and present the proof of purchase that they gave you on the day of purchase.
Should any malfunctioning arise, the retailer will advise you what to do.
For the warranty to apply, you should ensure that the product was used in accordance
with the instructions for use and the purpose for use, and that you have at your disposal
the sales invoice or receipt stating the date of purchase, the name of the retailer, the
reference and the serial number of the product.
No coverage shall be given under this warranty if the following conditions are applicable:
The required documents have been modified or altered in order to take advantage of the
warranty. The manufacturing numbers, product brands or labels have been altered or
made illegible.
Interventions on the product have been made by an unauthorized person.
The product has been subjected to abnormal or improper use.
The product has been damaged by external factors such as lightning, over-voltage,
moisture, accidental damage, improper care as well as all Acts of God.
This present warranty does not affect the consumer rights that you may have under the
laws in effect in your country.
Important:
Should you return the product to the after-sales department, please ensure that you
return as well all the elements and accessories originally supplied with the product.
58
D380-D380A
Lexicon
Term Definition
Paging
(Paging)
The
Paging/pairing
mode allows you to associate devices
that have to operate in pairs (for example, a phone base
and its handset) in compliance with the GAP standard.
Private automatic branch
exchange
(PABX, Private Automatic
Branch eXchange)
A PABX is primarily used to connect the telephones of a
private entity on to the public telephone network.
3-way conference This service allows you to talk to two contacts
simultaneously.
GAP
(Generic Access Profile)
The GAP is a standard that allows the handsets of the
various manufacturers to be operated with the same base
and calls to be dialled on the line connected to the base.
Likewise, a single handset can work with several bases.
Intercommunication: Intercommunication establishes free communication
between several handsets from the same base.
Sagemcom Broadband SAS
Headquarters: 250, route de l'Empereur
92848 Rueil-Malmaison Cedex - France
Tél. +33(0)1 57 61 10 00 - Fax : +33(0)1 57 61 10 01
www.sagemcom.com
All rights reserved. Sagemcom Broadband SAS reserves the right to change the technical characteristics of its products and services or to stop
marketing them at any time. The information and specifications included are subject to change without prior notice. Sagemcom Broadband SAS tries
to ensure that all information in this document is correct, but does not accept liability for error or omission. No contractual document. All trademarks
are registered by their respective owners. Simplified joint stock company - Capital 35 703 000 € - 518 250 360 RCS Nanterre.
253459476B - 02/2012
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sagemcom D380A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sagemcom D380A in the language / languages: English as an attachment in your email.

The manual is 11,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info