Manual Sage SCP600 (page 6 of 56) (English, German, Dutch, French, Italian, Portuguese, Spanish)

714753

Zoom out

Zoom in

1/56

Assembly

ASSEMBLING THE JUICER

1. Pull the juice press arm up, away from the

motor base, until fully extended.

2. Place the juice collector onto the drive shaft on

top of the motor base, ensuring the juice spout

ts into the semi-circular groove at the front

of the motor base.

3. Insert the lter into the juice collector, aligning

the indent with arrow in the bottom of the lter

over the corresponding tab with arrow in the

juice collector.

4. Place the juicing cone onto the drive shaft and

press down lightly to lock the cone into position.

5. To insert the fruit dome, place it into the hole on

the underside of the juice press arm. The fruit

dome is magnetic and will stick into place.

6. Ensure the anti-drip juice spout is pushed

down into the pouring position.

DISASSEMBLING THE JUICER

1. Turn the juicer OFF at the ON/OFF button,

then unplug from the power outlet.

2. Pull the juice press arm up, away from

the motor base, until fully extended.

Close the anti drip spout by flipping it up.

3. Remove the fruit dome by pulling on it gently

to release the magnet

4. Lift the juice collector from the base with the

lter, juicing cone and fruit dome still in place.

Remove the cone and lter from the juice

collector over a sink for easier cleaning. Follow

recommended care and cleaning guidelines.

Functions

1. Ensure the juicer is correctly assembled and

a glass or jug is placed under the juice spout

before juicing.

2. Cut the citrus fruit in half by cutting across the

fruit segments, rather than across the tip ends,

to ensure more ecient juicing.

3. Plug the power cord into a 220–240V power

outlet, then press ON/OFF switch to ON.

4. Place a citrus fruit half, cut side down,

onto the juice cone and push down lightly

onto the spikes.

5. Grasp the handle and slowly lower the juice

press arm. Press down (in a gentle but rm

action) until the fruit dome is in contact with the

fruit skin. The motor will automatically start and

the juicing cone will begin to rotate. The juice

will be extracted from the fruit and ow through

the juice spout into the glass. The pulp and

seeds will collect in the lter.

6. The juicer juices very quickly so each

fruit half will be juiced in a few seconds.

To automatically stop the motor, lift the juice

press arm up to its extended position.

7. Remove the used fruit from the

juicing cone. Empty excess pulp

and seeds from the lter as required.

Repeat Steps 3–7 to continue juicing.

NOTE

The lter should be emptied when full with pulp

and seeds. The lter can be emptied during juicing

by turning the juicer OFF at the ON/OFF switch

and carefully removing the juicing cone and lter.

Clean and replace lter and juicing cone before

continuing to juice. Do not allow the lter to overll

as this may prevent correct operation or damage

the unit.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sage SCP600 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sage SCP600 Manual

Product: