111432
30
Zoom out
Zoom in
Previous page
1/104
Next page
30
MACHINE ACTIONS - CAUSES - SOLUTIONS
Problems Causes Solutions
The machine does not turn on. The machine is not connected to the
power source.
Connect the machine to the power source.
The coffee is not hot enough. The cups are cold. Preheat the cups with hot water.
Hot water or steam is not
dispensed.
The hole of the hot water/steam wand
is clogged.
Clean the hole of the hot water/steam using
a pin.
Make sure that the machine is turned off
and has cooled before performing this
operation.
Pannarello is dirty (if present). Clean the Pannarello.
The coffee is not creamy
enough.
(see note)
The coffee blend is unsuitable, the
coffee is not freshly roasted or the grind
is too coarse.
Change coffee blend or adjust the grind
(section 5.2).
The machine takes a long time to
warm up or the amount of water
dispensed from the wand is too
little.
The machine's water circuit is obstructed
by limescale build-up
Descale the machine.
The brew group does not come
out.
The brew group is out of place. Turn the machine on. Close the service door.
The brew group is automatically placed in
the correct position.
The dregdrawer is inserted. Remove the dregdrawer rst, then the brew
group.
The machine grinds the coffee
beans but no coffee comes out.
(see note)
Water tank is empty. Fill the water tank and prime the circuit
(section 4.4).
The brew group is dirty. Clean the brew group (section 9.1).
The circuit is not primed. Prime the circuit again by dispensing hot
water from the hot water/steam wand.
Rare event that occurs when the
machine is automatically adjusting the
dose.
Brew a few coffees as described in section
5.1.
The dispensing spout is dirty. Clean the dispensing spout.
The coffee is too weak.
(see note)
Rare event that occurs when the
machine is automatically adjusting the
dose.
Brew a few coffees as described in section
5.1.
Coffee is brewed slowly.
(see note)
The coffee grind is too ne. Change coffee blend or adjust the grind
(section 5.2).
The water circuit is not primed. Prime the circuit again by dispensing hot
water from the hot water/steam wand.
The brew group is dirty. Clean the brew group (section 9.1).
Coffee leaks out of the dispensing
spout
The dispensing spout is clogged. Clean the dispensing spout and its holes.
Note: These problems can be considered normal if the coffee blend has been changed or if the machine has
just been installed; in this case wait until the machine performs a self-adjusting operation as described in
section 5.1.
Please contact customer service for any problems not covered in the above table or when the suggested
solutions do not solve the problem.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Saeco Xsmall Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Saeco Xsmall Plus in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info