459484

Saeco RI 9913- SUP 016 E Manual

50
Zoom out
Zoom in
Previous page
1/53
Next page
97
CLEANING AND MAINTENANCE OPERATIONS
CLEANING AND MAINTENANCE OPERATIONS
98
key pressed till the desired amount is reached.
Attention: cappuccino amount can only
be programmed if the corresponding
programming function is enabled (see
page 87).
38
For cappuccino dispensing, fit suction pipe (26) of
the Cappuccinatore (25) in a milk container or in
another container. To prevent milk container
deformation, pierce it on the top to allow air entry.
Place the cup under dispenser (27) and press the
cappuccino selection key.
Cappuccino dispensing can be adjusted by turning
the special Cappuccinatore adjustment valve (28).
Note: it is suggested to use milk with low fat
amounts (1.5%).
For a better cappuccino dispensing, do not
activate the steam (9).
Cappuccinatore cleaning
Let the Cappuccinatore drain a full water container
after each cappuccino dispensing: in this way,
the device will be perfectly cleaned.
Incorporated safety devices
Automatic off
Should the service door be open, the machine
automatically switches off. If the central unit is not
mounted, only water and steam can be
dispensed.
Electronic grinding time control
As soon as the coffee bean container is empty,
grinding automatically stops after 20 seconds
approx. Fill the container with coffee beans, as
shown at page 86.
Electronic pump control
The machine switches off automatically as soon
as the water in the tank is under the minimum level
checked by a special water level indicator (73).
Fill the tank according to the procedure shown at
page 86.
Electronic temperature adjustment
Said adjustment controls the correct temperature to
brew coffee and to dispense hot water and steam.
Coffee brewing is automatically interrupted should
the water temperature be excessive (safety
thermostat and overheating safety device
activated).
Antigravel device
Even selected coffees may contain impurities.
To avoid damages, the coffee grinder is fitted
with an antigravel device against impurities.
Should gravel end up into the coffee grinder, you
will hear a strong and characteristic noise. Stop
the machine immediately otherwise the machine
will automatically stop within 20 seconds thanks
to the special electronic protection system.
Important: Do not start the machine before
the foreign body has been removed, otherwise
the motor may be damaged. Procedures: see
page 85, points 45-49.
Cleaning and maintenance
operations
General cleaning
To ensure a good coffee quality and a longer
working life, always keep the machine clean.
Before cleaning the machine, turn off the main
switch, unplug the machine and wait until it
cools down.
Do not immerse the machine into water or other
fluids: it may be irreparably damaged!
Do not wash parts of the machine in the
dishwasher!
Always handdry all parts of the machine, do not
dry them in the oven or microwave oven!
Water tank, drip tray, coffee grounds
container and coffee dispenser
39
In order to keep the service area and the central
unit (22) clean, daily empty the coffee grounds
container (1), after machine use.
The water tank (11), drip tray (2), cup holder grill
(3) and coffee grounds container (1) should be
washed periodically, using a non-abrasive solvent
and drying them carefully.
40
Coffee dispenser (4) may be removed for cleaning
operations. Unloose the screws and rinse the
dispensing tube thoroughly with hot water.
From time to time, clean the machine casing with
a damp cloth and dry it.
Clean pre-ground coffee container (14) with the
aid of the brush supplied, whenever necessary.
Central unit
Clean central unit (22) whenever the coffee
bean container is filled, or at least once a week.
Switch off the machine and open service door
(19). Remove grounds coffee container (1).
41
Remove central unit (22), by holding the handle
and shortly pressing the PRESS key.
Wash the central unit with hot water; do not
use any solvent.
42
Make sure there are no coffee residues on the
two steel filters: the upper filter can be removed
by unloosening and turning the plastic pin
anticlockwise using the tool supplied.
Dry thoroughly each central unit component, fit
the filter again and tighten it properly with the
screw .
43
Remove coffee rest drawer (23) and clean it,
using a non-abrasive solvent.
Clean the service area thoroughly and fit the
coffee rest drawer again.
44
By holding the central unit by its handle, slide it
back into its original position, making sure it is
correctly engaged. Then close the door. Fit the
coffee grounds container again.
When fitting the central unit, do not
press “PRESS” button: it may cause
irreparable damages to the machine!
Warning: if the central unit is not correctly
fitted, the following message will be displayed:
"BREW UNIT MISS "
The machine cannot dispense coffee.
Coffee grinder
Never fill the coffee grinder with water: it may
irreparably damage the machine!
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Saeco RI 9913- SUP 016 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Saeco RI 9913- SUP 016 E in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 1,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info