661048
40
Zoom out
Zoom in
Previous page
1/92
Next page
6
Before you start mowing, always check the condition and firm attachment
of the cutting blade. The blade attachment screw must always be tightened
by an authorised workshop. If the blade screw is too tight or too loose, the
blade coupling and cutter bar can become damaged or loose which can
lead to serious injuries. A worn or damaged blade must always be
replaced.
Pos: 11.8.10 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Auswechseln, Nachschleifen ... Auswuchten ...Messers Benzinmäher neu @ 10\mod_1250583617106_1521.docx @ 86710 @ @ 1
Changing, regrinding and balancing the cutting blade must be carried out
by an authorised professional workshop.
A wrongly assembled cutting blade coupling can allow the cutting blade
bar to get loose and cause severe injuries.
An improperly ground and imbalanced cutting blade can cause strong
vibrations and damage the lawn mower.
Pos: 11.8.11 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Auf festen Sitz des Zündkerzensteckers achten @ 13\mod_1280215290591_1521.docx @ 110043 @ @ 1
Make sure that the spark plug connector is firmly seated! Touching is only a risk if
the spark plug connector is not installed correctly.
Pos: 11.8.12 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Beschädigte Teile ersetzen @ 0\mod_1115186070093_1521.docx @ 1634 @ @ 1
For reasons of safety, always replace worn or damaged parts.
Pos: 11.8.13 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Schutzhandschuhe tragen @ 0\mod_1115186195468_1521.docx @ 1646 @ @ 1
Protective gloves must be worn at all times during maintenance and
cleaning work.
Pos: 11.8.14 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Zündkerzenstecker abziehen Mäher @ 25\mod_1377160770344_1521.docx @ 187055 @ @ 1
Maintenance and cleaning work may only be carried out on level surfaces
with the engine switched off and the spark plug connector disconnected.
Regular maintenance is essential for safety and top performance.
Pos: 11.8.15 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Kerzenstecker niemals bei laufendem Motor abziehen @ 13\mod_1280219056956_1521.docx @ 110075 @ @ 1
Never remove the spark plug connector when the motor is running! Risk: Electric
shock.
Pos: 11.8.16 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Tank nur im Freien entleeren @ 0\mod_1115186486750_1521.docx @ 1649 @ @ 1
If the tank has to be emptied, this should be done in the open, and with a cold
engine. Take care to ensure that no fuel is spilt.
Pos: 11.8.17 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Nur Originalersatzteile verwenden SABO+JD @ 26\mod_1377168488208_1521.docx @ 187532 @ @ 1
For reasons of warranty and safety, only genuine spare parts may be used.
Non-equivalent spare parts can damage the machine and are a safety hazard.
Pos: 12.1 /Innenteil/Beschreibung der Bauteile/1 BESCHREIBUNG DER BAUTEILE @ 0\mod_1115187892468_1521.docx @ 1664 @ 1 @ 1
7 DESCRIPTION OF COMPONENTS
Pos: 12.2 /Innenteil/Beschreibung der Bauteile/40-SPIRIT (SA1733) @ 45\mod_1470736688155_0.docx @ 514272 @ @ 1
40-SPIRIT (SA1733)
Pos: 12.3 /Innenteil/Beschreibung der Bauteile/Bild 40-Spirit SA1733 @ 43\mod_1468400617482_0.docx @ 502138 @ @ 1
Pos: 12.4 /Innenteil/Beschreibung der Bauteile/40-SPIRIT (SA1333), R40 (SA1308) @ 45\mod_1470736771854_0.docx @ 514299 @ @ 1
40-SPIRIT (SA1333), R40 (SA1308)
Pos: 12.5 /Innenteil/Beschreibung der Bauteile/Bild 40-SPIRIT_SA1333 @ 45\mod_1470649058283_0.docx @ 513311 @ @ 1
Pos: 12.6 /Innenteil/Beschreibung der Bauteile/Alle Modelle_dl_text_bold_8 @ 33\mod_1409212920947_1521.docx @ 245827 @ @ 1
All models
Pos: 12.7 /Innenteil/Beschreibung der Bauteile/Beschreibung der Bauteile 40-SPIRIT SA1733, SA1333, SA1308 @ 45\mod_1470737007678_1521.docx @ 514326 @ @ 1
1 Safety control bar for engine stop
2 Setting handle for adjusting cutting height (carrying handle at the back) with push-
button
3 Engine cover
4 Tank cap
5 Primer pump (SA1333, SA1308)
6 Air filter
7 Cutting height display
8 Carrying handle, front
9 Spark plug
10 Exhaust protection grid
11 Oil refill neck with dipstick
12 Ejector flap
13 Starter cable handle
Pos: 13.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 13.2 /Innenteil/Vorbereitende Arbeiten/1 VORBEREITENDE ARBEITEN @ 0\mod_1115194917734_1521.docx @ 1672 @ 1 @ 1
8 PREPARATION
Pos: 13.3 /Innenteil/Vorbereitende Arbeiten/Vorbereitende Arbeiten Text 40er SABO+JD @ 40\mod_1440671029109_1521.docx @ 418457 @ @ 1
The following parts are included in the packaging for assembly of the mower:
Mower with preassembled handle
Collecting bag, collecting bag frame, chute
Tool bag with the following contents:
Operator's manual with Declaration of Conformity
Warranty conditions (depending on model)
Various fixing parts.
In the unlikely event of a missing part, please contact your dealer.
Pos: 13.4 /Innenteil/Vorbereitende Arbeiten/Vor Montage... Holm und...Starterseilhalter...Zündkerzenstecker abziehen! Hinweis @ 32\mod_1408441229475_1521.docx @ 239124 @ @ 1
NOTE
Always remove the spark plug connector before fitting the bar and the starter
cable holder. Following assembly, at the latest before starting the engine, push
the spark plug connector back in place.
Pos: 13.5 /Innenteil/Vorbereitende Arbeiten/1.1 Führungsholm hochstellen (Abbildung A1 + E1 + B1 + O4) @ 22\mod_1359539068167_1521.docx @ 168210 @ 2 @ 1
Opening out the handle (Illustration A1 + E1 + B1 + O4 )
Pos: 13.6 /Innenteil/Vorbereitende Arbeiten/Bowdenzüge nicht knicken oder einklemmen WICHTIG @ 44\mod_1469603773573_1521.docx @ 508855 @ @ 1
IMPORTANT
Make sure the throttle cables are not kinked or jammed when lifting the
handlebars.
Pos: 13.7 /Innenteil/Vorbereitende Arbeiten/Führungsholm hochstellen Text 40er ab 2013, neuer HOLM UT @ 23\mod_1366800600985_1521.docx @ 172558 @ @ 1
Pull the folded-up Z-shaped guide spar apart and upward A1 .
When upper and lower handle are aligned tighten the two wing-nuts by hand E1 .
Push both ends of the bottom part of the handle with the toothed plastic adapters
backwards until they click into the toothed recess on the mower housing B1 .
In this way, three different handle heights can be set.
Tighten the two wing-nuts on both sides by hand B1 .
Insert the cable on the left hand side into the cable guide. This is to prevent the
cable from being trapped when folding the handle E1 .
Attach the Bowden cable to the bottom section of the guide spar with the aid of
cable tie from the tool bag O4 .
Pos: 13.8 /Innenteil/Vorbereitende Arbeiten/Holmhöhenverstellung...Umschlagen des Holms Hinweis 36er, 40er, 43er, 47er @ 13\mod_1280321957086_1521.docx @ 110481 @ @ 1
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sabo R40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sabo R40 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info