Pos: 21.2 /Innenteil/Störungsursachen und deren Beseitigung/1 STÖRUNGSURSACHEN UND DEREN BESEITIGUNG @ 0\mod_1115373523343_1521.docx @ 1904 @ 1 @ 1
17TROUBLESHOOTING
Pos: 21.3.1 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/1 Tabellenkopf @ 0\mod_1115374760156_1521.docx @ 1884 @ @ 1
Fault Possible cause Remedy
Pos: 21.3.2 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Motor läuft nicht an Elektro @ 13\mod_1280992241502_1521.docx @ 110776 @ @ 1
If the motor does not
start 5 seconds after
the unit is started
No power supply.
Connect the plug C2 .
Check the fuse.
Power cable damaged. Get it checked by an
authorised workshop.
Cutting height has been
set too low (grass is too
high and blocks the
starting of the motor).
Set a higher cutting height I .
Machine tilts when starting it.
Too much grass waste in
the housing.
Clean the cutting chamber of
grass, ensure that the gap
between fan and housing is
kept clean (pull the plug
first!).
Get it checked by an
authorised workshop.
Pos: 21.3.3 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Starke Erschütterungen (Vibrieren) @ 0\mod_1115377318234_1521.docx @ 1900 @ @ 1
Extreme vibration
Have it checked by an
authorized dealer
Pos: 21.3.4 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Schnitt unsauber, Rasen wird gelb, Elektro @ 0\mod_1125904144842_1521.docx @ 1899 @ @ 1
Unclean cut, lawn is
yellow
Blade blunt. Have it sharpened and
balanced by an authorized
dealer Q .
Cutting height too low. Adjust to higher cutting height
I .
Mowing too fast. Adjust mowing speed.
Insufficient overlapping
of cuts when mowing.
Tall grass conditions may
dictate that more overlapping
of cuts is required.
Lawn becomes matted. A lawn scarifier can remedy
the problem considerably
Pos: 21.3.5 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Auswurf verstopft, Elektro TurboSinal @ 0\mod_1125903118742_1521.docx @ 1887 @ @ 1
Ejection blocked
Turbo signal has not
been detected
J + K .
Empty the grass collector L .
Cutting height too low for
grass that is too high.
Adjust to higher cutting height
I .
Pushing mower too fast. Adjust mowing speed.
Grass not dry. Let grass dry.
Pos: 21. 3.6 /Innente il/Störung sursachen un d deren Beseit igung/Stör ungstabell enelemente/ Gemulchte G ras sieht schl echt aus He ckauswurf @ 5\mod_1183467132357_1521.docx @ 35950 @ @ 1
Mulched grass
appearance is poor:
clumps, excessive
clippings, rough cut.
Blade blunt. Have it sharpened and
balanced by an authorized
dealer.
Mulching rule not
followed (cut max. 1/3 of
the grass height; the
height of the grass to be
cut must be lower than
10 cm)
Adjust to higher cutting height
I .
Convert mower to rear
discharge U2 + S1 and
mow grass first with higher
cutting setting.
Travel speed too fast. Adjust travel speed.
Grass build-up under
deck.
Adjust to higher cutting height
I .
Insufficient overlapping
of cuts when mowing.
Tall grass conditions may
dictate that more overlapping
of cuts is required
Grass not dry. Adjust to higher cutting height
I .
Let grass dry.
Pos: 21.4 /Innenteil/Störungsursachen und deren Beseitigung/Störungsursachen und deren Beseitigung Text Elektro @ 0\mod_1125668481258_1521.docx @ 1906 @ @ 1
Repairs to electrical machines must always be performed only by qualified electricians.
Please do not repair them yourself.
In the case of faults and defects which have not been listed here, please contact the
nearest authorized dealer. This applies in particular to appliances with electrical motors,
as when these are repaired they must always undergo an insulation protection test.
Your authorized dealer will also help you if you do not wish to perform any of the
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Sabo 36-EL at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Sabo 36-EL in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.
The manual is 3,07 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
