628409
2
Zoom out
Zoom in
Previous page
1/2
Next page
B
Swashplate
[H0422-S]
- 1 x Swashplate Assembly.
- 2 x Bearings 30x
37x4mm.
- 6 x Uniballs M3x4
5 H3.
- 1 x Uniball M3x4
5 H18.
- 3 x Socket Head Cap
Screws M2x5mm.
- 4 x Socket Head Cap
Screws M2x8mm.
- 3 x Swasher
2x
5x0.5mm
Radius Arm
[H0132-S]
- 1 x Center Hub.
- 2 x Socket Head Cap Screws
M3x12mm.
- 1 x Socket Head Cap Screws
Shouldered M4x25mm.
- 1 x Metric Hex Nylon Nut M4.
Center Hub
[H0411-S]
- 2 x Radius Arms.
- 2 x Spacer Arm
3x
5x2.7mm.
- 2 x Spacer Arm
2.5x
4x6.3mm.
- 2 x Uniball Radius Arms.
- 2 x Socket Head Cap Screws M3x16mm.
- 2 x Socket Head Cap Screws M2.5x18mm.
- 2 x Washers
3x
4x0.5mm.
- 2 x Flanged Bearings
2.5x
6x2.5mm.
- 2 x Flanged Bearings
3x
7x3mm.
Linkage
[H0417-S]
- 2 x Linkages
M3x50mm.
- 4 x Plastic Ball Links.
Damper Derlin
[H0426-S]
- 3 x H0426-A.
- 3 x H0426-B.
- 3 x H0426-C.
- 3 x Washers
10x
16x1mm.
- 3 x Washers
10x
16x0.2mm.
- 3 x Orings 3050.
Recommendations
- These parts should be used only with models SAB Goblin
- Please follow all the instructions shown in the Goblin main manual. In this manual please read Chapther 2, Important notes
- Use Loctite on all threads.
- Put a small amount of grease inside the hub and the O-Ring.
- Check for axial play of the spindle at least after the first 10 flights and add shims if necessary.
- Firmly tighten the blades before flight.
ABOUT HPS2
The new HPS 2 head offers an independent dampening system
for each blade grip, there are three dampening settings:
A = Soft for smooth response.
B = Medium.
C = Firm for direct and precise response.
We recommend starting with the medium setting.
For safety reasons we suggest to not exceed 2300 rpm.
Spare Parts
- 2 x Blade Grip.
- 2 x
Thrust Bearing
10x
18x5.5mm.
- 4 x
Bearing
10x
19x5mm.
- 2 x Washer
10x
16x1mm.
- 2 x Buttom Head Cap Screw M4x8mm.
Blade Grip
[H0182-S]
- 2 x Blade Grip Arm.
- 2 x Socket Head Cap
Screw M4x10mm.
- 2 x Uniball M3x3.5 Ø5 H5.5.
Blade Grip Arm
[H0183-S]
Spindle Shaft
[H0412-S]
- 2 x Spindle Shaft.
- 2 x Pin 5mm.
- 4 x Socket Head Cap
Screw M2.5x6mm.
- 2 x Socket Head Cap
Screw M6x10mm.
- 2 x Washer Ø6,3xØ15x1.
Uniball M3x3.5 Ø5 H5.5
[H0437-S]
- 2 x Uniball M3x3.5x
5H5.5.
TIPS:
RECOMMENDATIONS
- These parts should be used only with models
SAB Goblin 630, 700, 770, Speed, URUKAY
- Please follow all the instructions shown in the
Goblin main manual. In this manual please read
Chapter 2, Important notes
- Use Loctite on all threads.
- Put a small amount of grease inside the hub and
the O-Ring.
- Check the spindle for axial play at least after the
first few flights and add shims as necessary,
slight axial preload is optimal.
The blade grips must move freely, but they
should not move just under their own weight.
- Firmly tighten the blades before flight.
Left Side
Right Side
* To remove the dampeners,
you can use a flathead screwdriver
through the hole as shown.
* Clock-wise, counter clock-wise thread
* By turning the linkages you can adjust tracking.
If tracking is adjusted correctly, you’ll see the metal
part line up around in the center of the opening.
Detail B
SPARE PARTS
Page 2
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for SAB Heli Division Head HPS2 - H0428 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of SAB Heli Division Head HPS2 - H0428 in the language / languages: English as an attachment in your email.

The manual is 5,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info