628368

SAB Heli Division Goblin 700 speed Manual

31
Zoom out
Zoom in
Previous page
1/48
Next page
TAIL BELT TENSION
*Check the proper assembly of the tail boom.
*Check that the aluminum part of the tube is against the M3 stop screw.
*Loosen the tail group by loosening the 4 M3 screws.
*Install the belt onto the pulley, taking care to respect the direction of rotation (
figure 1
).
*Rotate the tail drive several times by hand.
*Load the spring by a rotation of
270°
the tensioning arm (
clockwise
)
*Tension the boom until the tensioning arm is aligned with the frame.
*Tighten the 4 screws.
*Check that the tail output shaft is perpendicular to the tube. (
figure 2
)
*In
figure 3,4,
5 you can see the three conditions, ok, too loose and too tight.
NOTE
. To disassemble the tail boom it is possible to remove the pulley H0101-S without loosening
the tail unit. Remove the locking screw and pull down.
CANOPY QUICK REALISE
Allows for quick installation and removal of the canopy. The canopy hole must be 12 to 12.5 mm in
diameter.
You can enlarge the hole slightly to optimize the vertical position of the canopy itself.
Always ensure the proper installation and locking before each flight. The lock button must always
come out to ensure locking.
It is recommended to attempt removal by forcing the canopy slightly to ensure proper locking.
CANOPY QUICK REALISE
CANOPY
On the Goblin, the canopy touches the frame. To avoid triggering vibration, it is necessary to
attach an adhesive foam tape to the canopy (
figure 6
). To lock the canopy saver, normal is
possible to use a litle bit of CA Glue
CANOPY
The Goblin Speed canopy has a very effective locking system in order to eliminate vibrations and
optimize aerodynamics.
You must install the following to complete the canopy assembly:
Adhesive foam tape (Fig 6), Canopy edge protection (Fig 8), and Canopy grommets (Fig 6)
To install the canopy:
· Insert the canopy from the front up to the area of the block shown in Fig. 7
· Join the edges and tighten the M3 bolts(Fig.8)
· Insert the H0378 knobs (Fig.9)
The canopy hole must be 12 to 12.5 mm in diameter. Initially is 9 mm. You can enlarge the hole
slightly to optimize the vertical position of the canopy itself.
Copyright © 2013 - SAB Heli Division - All rights reserved
Page 29
Chapter 13, Installation Of The Boom, Canopy
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for SAB Heli Division Goblin 700 speed at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of SAB Heli Division Goblin 700 speed in the language / languages: English as an attachment in your email.

The manual is 58,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of SAB Heli Division Goblin 700 speed

SAB Heli Division Goblin 700 speed Additional guide - English - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info