557213
28
Zoom out
Zoom in
Previous page
1/309
Next page
MAINTENANCE
(Recommended spark plug: NGK BR-6HS;
CHAMPION RL86C.)
CLEANING FUEL CUP
( Fig. 21)
Inspect fuel cup (47) for water and dirt.
If dirt or water is present, close the fuel valve and
remove the fuel cup. Using a wrench, grasp the
square on the bottom of the fuel cup and turn
clockwise.
After removing dirt and water, wash the fuel cup with
kerosene or petrol. Reinstall securely to prevent
leakage.
NOZZLE MAINTENANCE
( Fig. 22)
Excessive pump pressure (a pulsing sensation felt while
squeezing the trigger) may be the result of a clogged or
dirty nozzle.
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Remove the nozzle (11) from the spray wand.
NOTE: Never point the spray wand at your face.
Using the nozzle cleaning tool (15) provided with this
product, free any foreign materials clogging or
restricting the nozzle.
Using a garden hose, flush debris out of nozzle by
back flushing (running the water through the nozzle
backwards or from the outside to the inside).
Reinstall the nozzle then reconnect the nozzle to the
spray wand.
Turn on the water supply and start the engine.
REPLACING THE FUEL HOSE
Replace the fuel hose every 1,000 hours of use. If fuel
leaks from fuel hose, replace the hose immediately.
PUMP MAINTENANCE
We recommend having the pump oil changed every 100
hours to ensure longer life of the machine. This service
should be performed by an authorized service center.
(Recommended pump oil: 15W40)
STORING THE PRESSURE WASHER
It is important to store this product in a frost-free area.
Always empty water from all hoses, the pump, the fuel
tank, and the detergent bucket before storing.
NOTE: Use of a fuel stabilizer and pump saver will give
you better performance and increase the life of the
machine.
Discharge Fuel:
Drain the fuel tank completely. Stored petrol can go stale
in 30 days.
Remove the drain screw from the carburetor float
chamber and discharge fuel.
Engine Oil:
Drain the oil and replace with fresh, clean oil.
Spark Plug:
Disconnect spark plug wire and remove the spark
plug. Pour about a teaspoon of clean, air-cooled,
four-stroke oil through the spark-plug hole into the
combustion chamber.
Leaving the spark plug out, pull the starter cord two or
three times to coat the inside of the cylinder wall.
Inspect the spark plug and clean or replace, as
necessary.
Reinstall the spark plug, but leave the spark plug wire
disconnected.
Air Filter:
Clean the air filter.
Hoses, detergent bucket, and pump:
Flush the injection tube with clean water for 1 - 2
minutes. Remove all hoses. Empty the pump by pulling
on the recoil starter about 6 times. This should remove
most of the liquid from the pump.
PREPARING FOR USE AFTER STORAGE
Pull the recoil starter grip three or four times to clean
oil from the combustion chamber.
Remove spark plug from the cylinder. Wipe oil from
the spark plug and return it to the cylinder.
Reconnect the spark plug wire.
Refuel the machine as described earlier in the
operator’s manual.
20
English
GB
F D E I P NL S DK N FIN GR HU CZ RU RO PL SLO HR TR EST LT LV SK BG
PPW-3000_25lgs.qxd 3/26/01 11:52 PM Page 20
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ryobi PPW-3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi PPW-3000 in the language / languages: All languages as an attachment in your email.

The manual is 30,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info