390130
13
Zoom out
Zoom in
Previous page
1/121
Next page
DESCRIPTION
1. Variation speed control
2. “ON/OFF” switch trigger
3. Power cord guard
4. Dust bag assembly
5. Sanding pad
6. Paper clamp
7. Live tool indicator
8. Puncher
9. Sandpaper
10. Base
11. Non-adhesive sandpaper
FEATURES
Your sander is suitable for sanding with coarse, medium,
and fine grit sandpaper. It will produce a fine scratch free
finish when used to sand with the grain on wood surfaces.
It has been designed so that flush corner sanding on
three sides of the sander is possible.
Your sander has a comfortable palm grip handle that
provides maximum one-hand comfort, and reduces
operator fatigue during continuous sanding operations.
Your sander also has a built in dust collection that
collects dust through punched holes in the sandpaper
and cushion (Fig. 5).
Before attempting to use your sander, familiarize
yourself with all operating features and safety
requirements.
SWITCH (1)
ELECTRONIC SPEED CONTROL
The electronic speed control allows the operator to adjust
speed to meet varity sanding material from tough heavy
grained timber to delicate veneer.
This tool is equipped with a simple switch control. To turn
the sander "ON", slide the switch to the left.
Slide the switch to the right to turn the sander "OFF".
WARNING
Do not allow familiarity with your sander to make
you careless. Remember, a careless fraction of a
second is sufficient to inflict severe injury.
OPERATION
WARNING
Your sander should never be connected to power
supply when you are assembling parts, making
adjustments, assembling or replacing sandpaper,
cleaning, or when not in use. Disconnecting
sander will prevent accidental starting that could
cause serious personal injury.
INSTALLING NON-ADHESIVE SANDPAPER
(Fig. 5)
Inspect sandpaper before installing. DO NOT use
broken or defective sandpaper.
Unplug your sander.
WARNING
Failure to unplug your sander could result in
accidental starting causing possible serious
personal injury.
If replacing sandpaper, remove old sandpaper.
To remove paper, release paper clamp by lifting up on
lever, and disengaging it from the tab, and allowing
the lever to lower.
Insert end of new 1/3 sheet sandpaper approximately
1/2 in. (12.7 mm) under the paper clamp.
Note: 1/2 in. (12.7 mm) clamping of sandpaper is
necessary for multi-sheet stacking of paper.
Lift up on lever and lock into place. Apply downward
pressure to conform sandpaper to plate.
Wrap sandpaper around cushion. Lift lever on
opposite end of sander and insert loose end of
sandpaper under paper clamp. Fit sandpaper tight
against cushion.
Lift up on lever and lock into place.
Multiple sheets of sandpaper can be installed at one
time for convenience.
ATTACHING ADHESIVE (HOOK & LOOP)
SANDPAPER
Unplug the sander.
Align holes in hook and loop type sanding paper with
holes in pad, then carefully press fuzzy side of
sanding paper against pad as tightly as possible.
Note: Hook and loop type sanding papers can be
reused for the life of the sanding abrasive. It is
recommended that you keep the sanding paper
backing pad clean to provide for best adhesion. Clean
occasionally by brushing lightly with a small brush.
9
GB
English
F D E I P NL S DK N FIN GR H CZ RUS PL
RO
SLO TR
HR
ESS-1890ESS-2590V(EU)-25.qxd 8/15/04 4:52 PM Page 9
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ryobi ess 2590 v at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi ess 2590 v in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info