Manual Ryobi eid 500 re (page 9 of 83) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

388689

Zoom out

Zoom in

1/83

THANK YOU FOR BUYING A RYOBI PRODUCT

To ensure your safety and satisfaction, carefully read

through this OWNER'S MANUAL and the SAFETY

INSTRUCTIONS before using the product.

INSTRUCTIONS FOR SAFE HANDLING

■ Make sure that the tool is only connected to the voltage

marked on the name plate.

■ Never use the tool if its cover or any bolts are missing.

If the cover or bolts have been removed, replace them

prior to use. Maintain all parts in good working order.

■ Always secure tools when working in elevated positions.

■ Never touch the blade, drill bit, grinding wheel or

other moving parts during use.

■ Never start a tool when its rotating component is

in contact with the work piece.

■ Never lay a tool down before its moving parts have

come to a complete stop.

■ ACCESSORIES: The use of accessories or attachments

other than those recommended in this manual might

present a hazard.

■ REPLACEMENT PARTS: When servicing use only

identical replacement parts.

■ WARNING: When using electric tools, basic safety

precautions, including the following, should always be

followed to reduce the risk of fire, electric shock and

personal injury.

■ Keep work area clean. Cluttered areas and benches

invite injuries.

■ Consider work area environment. Do not expose

power tools to rain. Do not use power tools in damp

or wet locations. Keep work area lit. Do not use

power tools where there is risk of fire or shock

■ Guard against electric shock. Avoid body contact with

earthed or grounded surface (e.g. pipes, radiators,

ranges, refrigerators).

■ Keep children away. Do not let visitors touch

the tool or extension cord. All visitors should be kept

from area.

■ Store idle tools. When not it use, tools should be stored

in a dry, high or locked up place, out of reach of children

■ Do not force the tool. It will do the job better and safer

at the rate for which it was intended.

■ Use the right tool. Do not force small tools or

attachments to do the job of a heavy duty tool.

Do not use tool for purposes not intended.

■ Use safety glasses. Also use face or dust mask if

the cutting operation is dusty.

■ Do not abuse the cord. Never carry the tool by the cord

or yank it to disconnect it from the socket. Keep the cord

away from heat, oil and sharp edges.

■ Do not overreach. Keep proper footing and balance

at all times.

■ Maintain tool with care. Keep cutting tools sharp

and clean for better and safer performance. Follow

instructions for lubrication and changing accessories.

Inspect tool cord periodically and if damaged have

it repaired by an authorized service facility. Inspect

extension cords periodically and replace if damaged.

Keep handles dry, clean and free from oil and grease

■ Disconnect tools when not in use, before servicing

and when changing accessories such as blades,

bits and cutters.

■ Avoid unintentional starting. Do not carry a plugged-in

tool with a finger on the switch. Ensure that the machine

is switched off before connecting to the power supply.

■ When tool is used outdoors, use only extension cords

intended for outdoor use.

■ Stay alert. Watch what you are doing. Use common

sense. Do not operate tool when you are tired.

■ Check for damaged parts. Before further use of the

tool, a guard or other part that is damaged should be

carefully checked to determine that it will operate

properly and perform its intended function. Check for

alignment, breakage of parts, mounting and any other

conditions that may affect its operation. Aguard or other

part that is damaged should be properly repaired

or replaced by an authorized service centre unless

otherwise indicated in this instruction manual.

Have defective parts replaced by an authorized

service facility. Do not use the tool if the switch does

not turn it on and off.

■ Make sure that the drill bit is securely mounted.

An incorrectly mounted bit is extremely dangerous

since it can fly off or break during drilling.

■ Dress properly. Do not wear loose clothing or jewellery,

they can be caught in moving parts. Protective gloves

and non-skid footwear are recommended when

working outdoors. Wear protective hair covering

to contain long hair.

■ Hold the tool securely with both hands. If not held

securely, accidents or injury may result.

■ Never touch the chuck or metal body parts when

drilling walls, floors, or other surfaces covering

electrical wiring. Hold the tool only by the plastic

handle to prevent electric shocks.

■ While operating, the work piece must be securely

held with a vice or clamp to prevent it from moving

due to the drill rotation.

English

F D E I P NL S DK N FIN GR H CZ RUS PL

SLO TR

EID-500RE&750REN_20 lgs 26/08/05 11:30 Page 5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi eid 500 re in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ryobi eid 500 re Manual

Product: