491255

Ryobi EBS-9576V Manual

11
Zoom out
Zoom in
Previous page
1/77
Next page
7
GB
F D E
English
I P NL S DK N FIN GR H CZ RUS RO PL
CHANGING THE ABRASIVE BELT (FIG. 3 TO 5)
NOTE!
Be sure that the arrow inside of the belt is pointing in
the same direction as that of the tool.
■ Push the lever down to the original position (Fig. 5).
CAUTION!
Ensure that your fingers are not trapped.
TRACKING ADJUSTMENT (FIG. 6)
The belt life will be increased by using the tracking
adjustment.
Turn the tool upside down and hold if firmly with one hand, then
start the tool and observe the tracking of the sanding belt.
Stop the tool and adjust the tracking of the belt by rotating
the tracking knob until the edge of the belt is even with the
outer edges of both the front and rear rollers.
CAUTION!
Check that the belt does not rub against the
tool’s frame.
OPERATING (FIG. 7)
NEVER COVER AIR VENTS SINCE THEY MUST
ALWAYS BE OPEN FOR PROPER MOTOR COOLING.
MAKE SURE THAT THE WORK PIECE IS FREE OF
NAILS AND OTHER FOREIGN OBJECTS THAT
COULD TEAR THE ABRASIVE BELT.
Hold the tool firmly with both hands. Turn the switch on
and permit the rotation of the abrasive belt to reach full
speed. Then gently place the tool on the work piece
surface. Move the tool back and forth. Never exert
excessive pressure on the tool. The weight of the tool
applies adequate pressure. Excessive pressure will
retard the abrasive action, leave an uneven finish and
cause extra wear to both the tool and the abrasive belt.
Always lift the tool off the work piece before turning the
switch off.
CLAMP
(Optional accessory)
The clamp is designed to stabilize the tool when using it
in the bench configuration.
MOUNTING & ADJUSTING THE OPTIONAL
SANDING FRAME FOR EBS-7576 ONLY (FIG. 8)
Put the sanding frame on the belt sander and attach four
slot into slot holder (25).
By turning the adjustment bolt counterclockwise,
the sanding frame will rise and can be taken out.
If turning clockwise, it will down and the depth will be added.
Fine adjustment of the abrasive action is possible by
turning the adjustment bolt (24).
MOUNTING & ADJUSTING THE OPTIONAL
SANDING FRAME FOR EBS-9576V & EBS-1310V
ONLY (FIG. 9)
Put the belt sander on the sanding frame and attach four
slot into slot holder (25).
By turning the adjustment bolt counterclockwise,
the sanding frame will down and can be taken out.
If turning clockwise, it will raise and the depth will be added.
Fine adjustment of the abrasive action is possible by
turning the adjustment bolt (24).
MAINTENANCE
After use, check the tool to make sure that it is in top
condition.
It is recommended that you take this tool to a Ryobi
Authorized Service Centre for a thorough cleaning and
lubrication at least once a year.
DO NOT MAKE ANY ADJUSTMENT WHILE THE MOTOR
IS IN MOTION.
ALWAYS DISCONNECT THE POWER CORD FROM THE
RECEPTACLE BEFORE CHANGING REMOVABLE
OR EXPENDABLE PARTS (BLADE, BIT, SANDING
PAPER, ETC.), LUBRICATING OR WORKING ON THE UNIT.
WARNING!
To ensure safety and reliability, all repair should
be performed by an AUTHORIZED SERVICE
CENTRE or other QUALIFIED SERVICE
ORGANIZATION.
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
BELT SANDER -MANUAL 4/08/03 9:30 Page 7
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ryobi EBS-9576V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi EBS-9576V in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info