391211
8
Zoom out
Zoom in
Previous page
1/70
Next page
DESCRIPTION
5. ON / OFF switch
6. Lock-on feature
7. Disc flange
8. Clamp nut
9. Spindle shaft
10. Wrench
11. Spindle lock button
12. Wheel guard lock lever
13. Live tool indicator
STANDARD ACCESSORIES
Aux. handle (3).
A grinding wheel is included in the standard accessories
for some countries.
APPLICATION
Use only for the purpose listed below:
- Grinding
NOISE BUILD-UP
Noise (sound pressure level) in the workplace can exceed
85 dB (A). In this case, sound insulation and hearing
protection measures must be taken by the operator.
ON / OFF SWITCH
To switch on the unit – use your index finger to
depress the on / off switch (5).
To switch off the unit – just release the on / off
switch (5).
LOCK-ON FEATURE (FIG. 1)
Your grinder has a lock-on feature that is convenient when
continuous operation over an extended period of time is
required. To lock-on, depress the on / off switch and push
in the safety lock located on the side of the handle.
While holding the safety lock pushed in, release the switch.
To release the lock, depress the switch and release it.
MAIN HANDLE
The main handle can be set to any of three positions
(0 and 90 degree right and left) by pressing the rotary
lock button (4).
TOOL-LESS WHEEL GUARD
Release the wheel guard lock lever (12) then turn the
tool-less wheel guard (2) to the desired position.
The max. turning axle is 90º on either side; otherwise the
guard can’t be locked.
MOUNTING THE GRINDING WHEEL
Attach the disc flange (7), the grinding wheel (1) and
the clamp nut (8) to the spindle shaft (9).
Be sure that the disc flange is properly seated on the
spindle shaft.
Depress the lock button (11) located on the right side
of gear case.
Using the wrench (10) provided, tighten the clamp nut
in a clockwise direction.
WARNING
Check carefully whether or not there are
cracks in the wheel. Replace a cracked wheel
immediately.
OPERATING (FIG. 3)
KEEP SAFETY GUARDS IN PLACE.
NEVER COVER THE AIR VENTS SINCE THEY
MUST ALWAYS BE OPEN FOR PROPER
MOTOR COOLING.
The key to efficient operating is controlling the pressure
and surface contact between the disc and work piece.
Flat surfaces are ground at an acute angle, usually 10 to
20 degrees with the work piece. Allow the disc to reach
full speed before starting to grind. Too great an angle
causes concentration of pressure on a small area which
may gouge or burn work surface.
LIVE TOOLINDICATOR
This tool features a live tool indicator (13) which
illuminates as soon as the tool is connected to the supply.
This warns the user that the tool is connected and will
operate when the switch is pressed.
MAINTENANCE
After use, check the tool to make sure that it is in good
condition. It is recommended that you take this tool to a
Ryobi Authorized Service Center for a through cleaning
and lubrication at least once a year.
5
GB
English
F D E I P NL S DK N FIN GR H CZ RUS PL
RO
SLO TR
HR
EAG-8512R_20 lgs 6/10/05 14:58 Page 5
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ryobi eag 8512 r at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi eag 8512 r in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info