383633
8
Zoom out
Zoom in
Previous page
1/73
Next page
PRODUCT SPECIFICATIONS
18V
Blade Stroke 22 mm
Motor 18 V
Maximum Cutting Thickness (wood) 60 mm
No Load Speed 0-3000 min
-1
Switch Variable Speed
FEATURES
1. LOCK-OFF BUTTON
2. DEPRESS HERE TO PULLSWITCH TRIGGER
3. SWITCH TRIGGER
4. BLADE CLAMP LOCK / RELEASE LEVER
5. SAW BLADE
6. BASE (SHOE) ASSEMBLY
7. BATTERY PACK (NOT INCLUDED)
8. LATCHES
9. DEPRESS LATCHES TO RELEASE
BATTERY PACK
10. BLADE CLAMP
11.TON INSTALL/TO RELEASE
12. TO LOCK
13. BLADE SHOWN CORRECT IN SAW BAR
OPERATION
WARNING
Always remove battery pack from your saw when
you are assembling parts, making adjustments,
assembling or removing blades, cleaning,
or when not in use. Removing battery pack will
prevent accidental starting that could cause
serious personal injury.
TO REMOVE / ATTACH BATTERY PACK
(NOT INCLUDED)
See Figure 2.
TO REMOVE
Locate latches on side of battery pack and depress
both sides to release battery pack from your saw.
Remove battery pack from your saw.
TO ATTACH
Place the battery pack in your saw aligning raised rib
on battery on battery pack with groove in saw's
battery port. See figure 2.
Make sure the latches on each side of the battery
pack snap into place and battery pack is secured to
saw before beginning operation.
TO INSTALL SAW BLADE
See Figure 3.
Remove battery pack. See figure 2.
WARNING
Failure to remove battery pack from saw could
result in accidental starting causing possible
serious personal injury.
Lift blade clamp lock/release lever on side of saw.
Insert saw blade between blade clamp and saw bar.
Lock blade clamp lever.
Replace battery pack.
GENERAL CUTTING
See Figure 4.
Hold your saw firmly in front of and clearly away from you.
Make sure saw blade is clear of any foreign material.
Be sure material to be cut is held firmly. Small work pieces
should be securely clamped in a vise or with clamps to
the work bench or table. Mark the line of cut clearly.
Depress the lock-off button, then pull switch trigger to start
the cutting action. Place the base assembly against the
work, then move the blade into the work. Do not force.
Use only enough pressure to keep the saw cutting.
Let the blade and saw do the work. Use of excessive
pressure that causes bending or twisting of the blade
may result in broken blades.
PLUNGE CUTTING
See Figure 5.
Mark the line of cut clearly. Choose a convenient starting
point inside the area to be cut out and place the tip of the
blade over that point. Rest front edge of base assembly
on work and hold firmly in position. Depress the lock-off
button, then pull switch trigger to start the cutting action.
WARNING
Make sure blade does not touch work until motor
reaches full speed, since this could cause loss of
control resulting in serious injury.
With saw blade at full cutting speed, slowly tilt saw
downward until tip of blade starts cutting work.
After blade penetrates work, tilt saw until blade is
perpendicular to the work.
5
GB
English
F D E I P NL S DK N FIN GR H CZ RUS PL
RO
SLO TR
HR
CRP-1801DM 10/05/05 11:38 Page 5
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ryobi crp 1801 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi crp 1801 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info