Manual Ryobi CHI-1442 (page 16 of 142) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

491254

Zoom out

Zoom in

1/142

OPERATION

SELECTING DRIVE OR DRILL SETTING

Using the chart below, choose correct speed and mode

the type of bit, fastener, and material you will be using.

APPLICATION

CHD-1442/

CHP-1802

Fig.5

CHI-1442/

CHI-1802

Fig.6

Lag screws up to 9.5 mm dia.

by 38mm long

Concr

ete screws

1/LOW

2/HIGH

Drill bits up to 6.35 mm

Self tapping scews

2/HIGH 1/L

Deck or wood screws up to

Small

screws or delicate work

that

requires more control

1/L

OW 2/HIGH

Deck or wood screws #8 up to

Scre

ws for rough work where

spee

dismoreimportantthan

prec

ise control

2/HIGH

1/LOW

2/HIGH

KEYLESS CHUCK (Fig.7)

The drill has a keyless chuck to tighten or release drill

bits in the chuck jaws. The arrows on the chuck indicate

which direction to rotate the chuck body in order to LOCK

(tighten) or UNLOCK (release) the drill bit.

WARNING

Do not hold the chuck body with one hand and

use the power of the drill to tighten the chuck

jaws on the drill bit. The chuck body could slip in

your hand, or your hand could slip and come in

contact with the rotating drill bit. This could cause

an accident resulting in serious personal injury.

INSTALLING BITS (Fig.7) / MAGNETIC BIT

HOLDER (Fig.8)

■ Lock the switch trigger by placing the direction of

rotation selector in the center position.

■ Open or close the chuck jaws to a point where the

opening is slightly larger than the bit size or the end

of the magnetic bit holder. Also, raise the front of the

drill slightly to keep the bit /bit holder from falling out

of the chuck jaws.

■ Insert the drill bit/bit holder.

■ Tighten the chuck jaws on the drill bit/bit holder

■ Insert a bit into the open end of the bit holder if

applicable.

REMOVING BITS (Fig.7) / MAGNETIC BIT

HOLDER (Fig.8)

■ Lock the switch trigger by placing the direction of

rotation selector in the center position.

■ Rotate the chuck sleeve clockwise to open the chuck

jaws.

■ Remove the drill bit/bit holder.

ADJUSTING THE TORQUE (Fig.9)

When using the drill-driver for various driving applications,

it becomes necessary to increase or decrease the torque

in order to help prevent the possibility of damaging

screw heads, threads, workpiece, etc. In general, torque

intensity should correspond to the screw diameter. If the

torque is too high or the screws too small, the screws

may be damaged or broken.

The torque is adjusted by rotating the torque adjustment

ring.

The torque is greater when the torque adjustment ring

is set on a higher setting. The torque is less when the

torque adjustment ring is set on a lower setting.

The proper setting depends on the type of material and

the size of screw you are using.

ADJUSTING THE POSITION OF THE

AUXILIARY HANDLE ASSEMBLY (FOR CHI-

1442/CHI-1802 ONLY) (Fig.10)

To adjust the position of the auxiliary handle assembly.

■ Loosen the handle assembly by turning the handle

counterclockwise.

■ Insert the auxiliary handle assembly in the desired

operating position.

■ Securely tighten by turning the auxiliary handle

clockwise.

English

E I

P NL

S DK N FIN GR

H CZ RUS PL

SLO TR

960931224-01B.indd 12960931224-01B.indd 12 7/20/07 11:16:39 AM7/20/07 11:16:39 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi CHI-1442 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ryobi CHI-1442 Manual

Product: