• The bottom of the carafe will be hot, set it down on an insulated mat.
• Rinse the carafe with hot water, to prewarm it, so it doesn’t take heat from the coee.
• To remove the lid, turn it to align the U with the u.
• Replace the lid in the same position, then turn it to align the L with the u.
• To open the spout for pouring, press the lever at the rear of the lid.
USING THE TIMER
Note: Make sure the clock is set to the correct time. Use the hr and min buttons.
1. Prepare the coee maker according to which mode you are using but do not press the + button to start brewing.
2. Press the
Y
button. The button will ash and the
Y
icon will ash on the display.
3. Within 10 seconds of pressing the
Y
button, use the hr and min buttons to enter the time you want your coee maker to start brewing.
4. If a time has previously been programmed, it will ash on the display otherwise the display will show the default setting of 8:00.
5. 10 seconds after you have nished entering the time, the
Y
button will stop ashing and remain lit. The
Y
icon on the display will also stop ashing
and remain lit. Your coee maker is now programmed to brew at the time you have entered.
• If you want to check the program time press the
Y
button. The programmed time will show for 3 seconds and then return to the time of day.
• If you want to cancel the timer before brewing has started, press and hold the
Y
button for 5 seconds until the
Y
light goes out and the
Y
icon
disappears from the display.
• If you want to stop the coee maker while it’s brewing, press the + button.
A QUICK CUP
If you want a quick cup of coee before the brewing cycle has nished:
1. You can remove the carafe at any time. The non-drip valve will prevent coee dripping on to the hotplate.
2. To prevent the lter holder overowing, replace the carafe on the hotplate within about 20 seconds.
3. When you replace the carafe on the hotplate the non-drip valve opens to let any remaining coee through.
CARE AND MAINTENANCE
GENERAL CLEANING
1. Unplug the appliance and let it cool.
2. Tip the contents of the lter holder into the bin.
3. Wipe all surfaces with a clean damp cloth.
4. Hand wash the carafe and lter holder. Wipe out the hopper with kitchen paper.
5. Wipe the shaded area shown in Fig H with a piece of damp kitchen paper. Use the brush if necessary to loosen any coee debris.
Note: If you haven’t used your coee maker for more than 4 weeks, we recommend that you follow the steps under BEFORE USING FOR THE FIRST TIME
before brewing coee again.
CLEANING THE GRINDER
The grinder can be disassembled in order to clean it. If you try to disassemble the grinder without rst removing any surplus coee beans, it will be very
dicult to reassemble correctly. Follow these steps:
1. Twist the coee bean hopper and lid counterclockwise until the d symbol aligns with the usymbol (Fig A).
2. Lift o the hopper, remove the lid and empty out any coee beans. Wipe out the hopper with kitchen paper.
3. Replace the lid then ret the hopper onto the coee maker aligning the d symbol with the usymbol. Twist the hopper clockwise until the d
symbol aligns with the lsymbol (Fig B).
4. Turn the grind control to the ne (l) setting.
5. Press the
g
button to select the 6 cup setting.
6. Press the + button. After a few moments the grinder will start. Once it has stopped, press the + button until the +light goes out.
7. Follow step 1 again to remove the bean hopper.
8. Turn the grind control to the r setting (Fig C).
9. Lift up the handle on the grinding head (Fig D).
10. Lift the grinding head out of the body of the appliance (Fig E). If it doesn’t lift out easily, make sure that the 3 marks on the grinding head are aligned
with the b markings (Fig G).
11. Use the cleaning brush to clean the grinding head and the area where it ts into the appliance. Do not use water.
12. Ret the grinding head by aligning the 3 marks on the grinding head with the b markings and pressing it down (Fig G). Fold the handle back down.
13. Turn the grind control to any of the grind settings.
14. Ret the hopper.
SELF CLEAN
After 60 brewing cycles, the display will show CLE and the c icon to indicate that the appliance needs descaling. Descaling ushes out the deposits that
naturally build up over time.
1. Use a proprietary brand of descaler suitable for use in plastic-bodied products. Follow the instructions on the package of descaler.
2. Pour the descaling solution into the water reservoir to the max mark.
3. Press the c button.
4. The automatic self clean process will start and will continue for about 45 minutes.
5. After the process has nished, your coee maker will switch o.
• Products returned under guarantee with faults due to scale will be subject to a repair charge.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Russell Hobbs 26520-56 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Russell Hobbs 26520-56 in the language / languages: Dutch as an attachment in your email.
The manual is 1.81 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
