489793

Russell Hobbs 18560-56 Manual

66
Zoom out
Zoom in
Previous page
1/68
Next page
66
Read the instructions, keep them safe, pass them on if you pass the appliance on.
Remove all packaging before use.
A IMPORTANT SAFEGUARDS
Follow basic safety precautions, including:
1 This appliance must only be used by or under the supervision of a responsible adult. Use and
store the appliance out of reach of children.
2 Don’t put the appliance in liquid, don’t use it in a bathroom, near water, or outdoors.
3 Unplug the appliance before fitting or removing attachments.
5 Keep your hands away from the blades – they’re sharp
6 Don’t fill with anything hotter than you can comfortably handle (i.e. liquid temperature
below 40°C).
7 The appliance is fitted with a safety switch to prevent the motor operating unless the jug is in
place and the lid correctly fitted. Don’t use this to switch the appliance on and off.
8 Don’t leave the appliance unattended while plugged in.
9 Don’t let the jug overflow. If liquid gets under the motor unit, it may be sucked into the motor,
damaging it.
10 Don’t run the motor continuously for more than 5 minutes, it may overheat. After 5 minutes
switch off for at least 2 minutes, to recover.
11 Don’t use accessories or attachments other than those we supply.
12 Don’t use the appliance for any purpose other than those described in these instructions.
13 Don’t use the appliance if it’s damaged or malfunctions.
14 If the cable is damaged, it must be replaced by the manufacturer, its service agent, or
someone similarly qualified, in order to avoid hazard.
household use only
C PREPARATION
1 Sit the motor unit on a dry, firm, level surface, near a power socket.
2 Route the cable so it doesn’t overhang, and can’t be tripped over or caught.
C FIT THE DRIVE SHAFT
3 Push the drive shaft up through the bottom of the jug.
4 Use the tabs to turn it clockwise and lock it to the bottom of the jug.
, If you need to rinse the jug, turn the tabs anti-clockwise, and remove the drive shaft first, to
avoid getting it wet.
C FIT THE JUG
5 Sit the jug on the motor unit, with the handle to the right of the controls.
6 Turn the jug clockwise to bring the handle between the controls.
C FIT THE ACCESSORY
7 To process, fit the chopper over the pillar in the centre of the jug.
8 To grate or slice:
a) Fit the disc support inside the pillar, over the drive shaft.
b) Lower the disc on to the disc support.
c) To slice, the slicing blade must be on top of the disc.
d) To grate, the slicing blade must be on the bottom of the disc.
C FIT THE LID
9 Hold the lid over the jug, with the safety switch to the right of the handle.
10 Lower the lid on to the jug.
11 Turn the lid clockwise to bring the safety switch into the gap at the top of the handle.
12 The controls will only operate with the lid and jug in this position.
… 66


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Russell Hobbs 18560-56 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Russell Hobbs 18560-56 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info