6
PACKAGE HANDLING INSTRUCTIONS
- The machine is supplied in a corrugated cardboard box with overall dimensions
59x38,5xh22 cm weighing 8,5 Kg.
- The box must be handled and stored in the upright position.
- Do not place any objects on the package that have a different sized base than
the package.
Unpacking instructions
- Carefully inspect the box before opening; if it is damaged or seems to have been
previously opened, do not open. Reject the box and register a complaint with the
carrier. Failure to do so will void the warranty.
- To unpack the machine, open the corrugated cardboard box, remove the machine and
set aside the bag of accessories.
To dispose of packaging materials, observe the regulations in effect where
the machine is installed, in consideration of recycling rules when applicable.
Inspection of package contents
The package contains:
- the machine equipped with power cord;
- 1 vacuum fixture (24) complete with 3,5 mm terminals for electric tools with ac-
cessories;
- n° 1 spare dust bag (16);
- a vacuum fixture (18) is available upon request complete with terminals and air
fittings m 5 for pneumatic tools (EP versions);
- a hose fixture is available upon request.
Safety and accident prevention instructions
The machine must only be used by trained and qualified personnel.
The machine must be located in a dry and well-ventilated area where air is chan-
ged at least once an hour with 50% of the total fresh air without the aid of special
ventilation systems. The temperature of the work area must be between 10°C and
35°C with humidity between 50% and 90%.
Always unplug the machine when not in use, before maintenance or cleaning and
before replacing the dust bag or filter. Do not pull the power cord to unplug the ma-
chine.
Keep the power cord away from heat, oil and sharp corners.
In the event of a blackout, turn the switch of the connected tool to the OFF position to
avoid it from accidentally starting when power returns. Do not expose the machi-
ne to rain.
Explosion or fire hazard
- Do not vacuum flammable or explosive dust (i.e. magnesium, aluminium, asbe-
stos, etc.);
- do not vacuum flammable or explosive liquids (i.e. petrol, thinners, etc.);
- do not vacuum aggressive liquids or substances (i.e. acids , bases, solvents,
etc.);
- do not vacuum sanding dust from surfaces treated with paints that have not
completed the catalyst cycle;
- immediately disconnect the vacuum from the electrical mains if dust is dischar-
ged;
- use the fire alarm system and leave the area in the event of fire.
TECHNICAL SPECIFICATIONS
OPERATING VOLTAGE
ABSORBED POWER
ABSORBED CURRENT
MAX TOOL POWER
MAX TOTAL POWER
MAX TOTAL ABSORBED CURRENT
VACUUM CAPACITY
DEPRESSION
WEIGHT
DIMENSIONS
NOISE LEVEL
FILTER SURFACES
FILTER CATEGORY
BAG CAPACITY
ELECTRICAL SOCKETS
3-WAY SWITCH
220/240 Vac - 50/60 Hz
1150 W
4 A
1 x 1000 W max
2150 W max
8,7 A
100 m3/h
1600 mm/H2O
6,5 Kg
cm 47,5 x 37 x h 20,5
75 dB (A)
m2 1,0
L
Kg 3,5 max
1
MAN - O - AUT
PNEUMATIC SECTION
INPUT AIR PRESSURE
MAX AIR CAPACITY
POWER FIXTURE
PNEUMATIC FITTINGS
6 bar max
1840 l/min
3/8” G femmina
1
PARTS OF THE TOOL
1 - bag housing lid
2 - 3-way switch
3 - suction adjustment control
4 - motor cooling air inlet
5 - identification plate
6 - slit for electric power cord
7 - transport handle
8 - shoulder belt hooks
9 - head clips
10 - accessory housing lid
11 - power cord
12 - electric tool socket
13 - suction pipe-union closing
14 - dust bag
15 - filter
16 - air exhaust
17 - hook slits
18 - pneumatic power inlet with hose fixture (optional)
19 - pneumatic tool coupling
20 - accessory brushes
21 - anti-shock support pedestal
22 - pneumatic tool fixture
23 - shoulder belt (optional)
24 - electric tool sleeve
25 - pneumatic tool sleeve (optional)
26 - electric tool fixture
START-UP
Minimum power supply requisites and connections:
Electric mains - Single-phase voltage 230V 50/60Hz with grounding wire
ated mm
2
3x1.5.
Compressed air mains - Working pressure not over 6 bar; the mainsmust supply
dehumidified and filtered air. Having assembled arubber hose fixture (optional)
(23), connect the machine to the pneumatic mains with a hose, whose length sup-
ports working pressure, of 10mm minimum internal Ø.
After having checked that the switch (2) is in the "O" position, insert the power cord
plug in a socket that supports the machine load.
14
20
23
Specific use
The machine is high stress qualified for industrial applications according to regu-
lations EN60335-1 and EN60335-2-69.
The machine is designed to vacuum dry sanding dust with all exposure limit va-
lues due to the work type. The machine supplies, simultaneously and near the
work area:
- the possibility of accessing energy sources to power electrical and pneumatic
tools without the use of extension cords;
- the availability of a sanding dust vacuuming system.
ENGLISH
Read the following instruction first before operate the product.
PICTOGRAPH
Important safety indications.
6
