489920

Rupes SR100 Manual

9
Zoom out
Zoom in
Previous page
1/34
Next page
9
PARTS OF THE TOOL
1 - Identification label
2 - On/off switch
2A - Switch lever
2B - Switch block
3 - Speed control
4 - Shaft
5 - Auxiliary handle
6 - Protective suction hood
7 - Roller retainer spacer
8 - Screw and washer
9 - Roller shaft
10 - Motor ventilation slots
11 - Connection for 29 mm suction hose
12 - Side guard with tightening knob
13 - Gauged plate
14 - Hood angle list
15 - Sliding pins
16 - Abrasive roller
17 - Keys
STARTING UP
Before starting-up the tool, ensure that:
- the packaging is complete and does not show signs of having been
damaged during storage or transport;
- the tool is complete; check that the number and type of compo-
nents comply with that reported in this instruction booklet;
- the power supply and socket outlet can support the load reported in
the table and that indicated on the tool identification plate reprodu-
ced and explained on page 11.
ASSEMBLING THE TOOL
- Loosen the side guard (12) by unscrewing the tightening knob and
turn it away to make room for assembly of the roller (18);
- position the roller on the roller shaft (9);
- if the roller is 50 mm long, also assemble the spacer provided (7);
- lock the assembly in place using the roller lock screw (8) and the
key provided (17);
- tighten the guard again;
- connect up the suction hose (11).
BEFORE STARTING THE TOOL
Ensure that:
- the power supply conforms with the characteristics of the tool;
- the power supply cable and plug are in perfect condition;
- the ON/OFF switch works properly though with the power supply di-
sconnected;
- all the parts of the tool have been assembled in the proper manner
and that there are no signs of damage;
- the ventilation slots are not obstructed;
- the tool must be connected to a suitable and efficient aspiration device.
STARTING AND STOPPING
SR100AEN
- Starting:
push the slide of the switch (2) forward; if the tool is to be
locked in the ON position, apply pressure to the front part of the sli-
de switch at the same time.
- Stopping:
release the slide or, if locked in position, apply pressure
to the back part of the switch and allow it to return to the stop posi-
tion.
SR200AE
- Starting: press the locking button (2B) on the upper section of the
handle, then the switch lever (2A). To lock the spindle shaft in order
to be able to carry out a continuous machining, press the switch
lever (2A), then the locking lever (2B) and hold it down while
releasing the switch lever (2A), so that is firmly maintained in
position.
- Stopping
: release the switch lever or, if this is blocked, push the
lever in order to release the locking button.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rupes SR100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rupes SR100 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info