489891

Rupes P850E Manual

7
Zoom out
Zoom in
Previous page
1/32
Next page
Position A= lowest speed
Position G = highest speed
Ensure that the drill is not allowed to jam for
longer than 2-3 seconde. Longer jamming can
lead to motor damage.
Important!
Continuous operation under strong load and
low speed can overheat the motor.
Allow the motor to cool down in no-load when
set at a high speed!
8. CHANGING DIRECTION OF ROTATION
(main rotation - clockwise)
Direction of rotation of the drill spindle is changed
using the reversing switch (3).
R = Clockwise (Right)
L = Anticlockwise (Left)
Important!
Presa the reversing switch until it reaches the
respective end position at the housing, i. e.
until it can be felt to engage!
The reversing switch is easiest to operate by
using the thumb and index or middle finger from
both sides.
Attention!
Change direction of rotation only when the
motor has ceased turning! When using the
drill as a screwdriver, the percussion mecha-
nism must be switched off. Switch-over by
means of the sliding switch (4).
When in middle position, the reversing switch
prevents the accidental activation of the full
wave electronic switch (1), for example when
changing tools or assembling/disassembling
the drill chuck.
9. PERCUSSION DRILLING DEVICE
The machine has an integrated percussion
mechanism and can be switched from normal
drilling to percussion drilling. The sliding switch
(4) allows switching from normal drilling to per-
cussion drilling or vice-versa while the machine is
in operation.
Normal drilling position:
Move switch (4) to the right in direction of normal
drilling.
Percussion drilling position:
Move switch (4) to the left in direction of percus-
sion drilling.
10. MECHANICAL 2-SPEED SELECTOR
The speed is selected by turning the selector dial
(5).
Position 1 = low speed
Position 2 = high speed
2-speed gearing gives the percussion drill added
versatility. The fast speed (position 2) is adjusted
for percussion drilling and nonnal small-hole drilling
up to a drill bit diameter of ap¬proximately 8 mm.
The slow speed (position 1) is adjusted for larger
drill bit diameters and for stirring applications.
11. THE SAFETY SLIPPLING CLUTCH
The slipping clutch begins to operate as soon as
the drill or the tool being driven is overloaded,
violently braked or jammed. The motor and tran-
smission continue to rotate, but the tool is no lon-
ger driven. This protects the driveline against
overloads and avoids damage to the gear teeth
caused by violent shocks.
12. CHUCK
The chuck is tightened with a turning moment
of 30 Nm. Only this guarantees that the chuck is
not unintentionally unwound from the drill spindle
in anticlockwise mode. Should the chuck be
undone from the drill spindle for the purpose of
replacement, the new chuck must be tightened
with a turning moment of at least 30 Nm before
the machine is used again.
The piane surfaces of the chuck and drill spindle
must be cleaned before a new chuck is mounted.
Caution!
Before disassembling and reassembling the
drill chuck, disconnect the machine from the
power supply, or remove the mains cable
module (6) from the grip using the locking
device button (7).
Caution!
When turning anticlockwise, it is possible
that the chuck loosens itself from the spindle.
For this reason make sure that the chuck sits
properly on the spindle.
13. OPERA
TING THE QUICK-CHANGE
CHUCK
This chuck has been developed especially for
use with percussion drills.
The fully-automatic spindle locking device ena-
bles a quick and problem-free tool change in the
chuck.
7
librettoP850E 21-08-2007 9:26 Pagina 7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rupes P850E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rupes P850E in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info