489881

Rupes LR21AE Manual

9
Zoom out
Zoom in
Previous page
1/34
Next page
9
PARTS OF THE TOOL
1 - Identification plate
2 - ON/OFF switch
3 - Speed control
4 - 29 mm Ø suction port
5 - Velcro faced abrasive disc backing pad
6 - Motor ventilation slots
7 - Disc pad fixing screws
8 - Dust bag
STARTING UP
Before starting-up the tool, ensure that:
-the packaging is complete and does not show signs of ha-
ving been damaged during storage or transport;
-the tool is complete; check that the number and type of com-
ponents comply with that reported in this instruction booklet;
- the power supply and socket outlet can support the load re-
ported in the table and that indicated on the tool identification
plate reproduced and explained on page 11.
REMOVING AND MOUNTING THE DISC PAD
- Unscrew the screws (7) on the disc pad;
- reverse the procedure when fitting the disc pad.
FITTING ABRASIVE PAPER DISCS
Press the abrasive disc into the pad ensuring that the holes in
the paper coincide with extraction holes in the disc pad.
BEFORE STARTING THE TOOL
Ensure that:
-the power supply conforms with the characteristics of the tool;
- the power supply cable and plug are in perfect condition;
-the ON/OFF switch works properly though with the power
supply disconnected;
-all the parts of the tool have been assembled in the proper
manner and that there are no signs of damage;
- the ventilation slots are not obstructed (6);
- the tool must be connected to a suitable and efficient dust ex-
traction system (4).
STARTING AND STOPPING
- Starting:
press the switch (2) down in position “I”.
- Stopping:
press the switch (2) up in position “O”.
TEST RUN
Start the tool and check that there are no unusual vibration, no di-
smatching of the abrasive paper disc.
Otherwise switch-off the tool immediately and eliminate the
cause.
ELECTRONIC RPM REGULATION
The rpm can be adjusted by rotating the wheel (3) located on the
rear of the tool. The choice of speed depends on the characteri-
stics of the abrasive paper disc and the material to be worked.
REPLACING THE ABRASIVE PAPER DISCS
- Used discs can be removed by simply tearing them off;
- new velcro discs are mounted by simply pressing them into
the backing pad, making sure that the holes cut in the disc
coincide with those in the backing pad.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rupes LR21AE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rupes LR21AE in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info