489877

Rupes LH31 Manual

8
Zoom out
Zoom in
Previous page
1/31
Next page
9
PARTS OF THE TOOL
1 - Identification plate
2 - Switch lever
3 - Switch block
4 - Electronic rpm regulation
5 - Spindle
6 - Auxiliary handle
7 - Buffer pad and abrasive disc tapered ring nut
8 - Buffer pad (on request) (LH22N-LH22EN-LH232N)
8A - Vulcofix pad (on request) (LH31N-LH22EN-LH232N)
9 - Wrenches (17 mm spanner and pin spanner)
10 - Motor ventilation slots
11 - Button to unlock or the pad (LH22N - LH22EN)
12 - Auxiliary protection
STARTING UP
Before starting-up the tool ensure that:
- the packaging is complete and does not show signs of having been
damaged during storage or transport;
- the tool is complete; check that the number and type of components
comply with that reported in this instruction booklet;
- the power supply and socket outlet can support the load reported in the
table and that indicated on the tool identification plate reproduced and
explained on page 11.
ASSEMBLING THE TOOL
Assemble the handle (6) and auxiliary hand protection (12); these can be
positioned either on the left or right of the tool body.
MOUNTING THE VULCOFIX PAD AND BUFFER PAD
If working with machines (LH31N - LH32EN - LH232N):
1. Insert the vulcofix pad (8A) on the spindle (5) (fig. 1).
2. Insert the abrasive disc;
3.Screw on the tapered ring nut (7) and tighten it using the pin spanner,
preventing the spindle from moving using the 17 mm. spanner (fig. 2).
If working with machines (LH22N - LH22EN):
1. Screw the buffer pad (8) on the spindle (5).
2.Lock the spindle by pressing button (11), while at the same time
rotating the pad until it locks position.
WARNING: never press the button to lock the pad orpas until the tool
has stopped moving and is perfectly stationary; the gear box or the
push button pin could be broken and the guarantee would be
invalidated.
3. Firmly tighten the disk.
4.Unlock the spindle by releasing the button and rotate the disc pad by
hand to ensure that it runs freely.
BEFORE STARTING THE TOOL
Ensure that:
- the power supply conforms with the characteristics of the tool;
- the power supply cable and plug are in perfect condition;
- the ON/OFF switch works properly though with the power supply
disconnected;
- all the parts of the tool have been assembled in the proper manner and
that there are no signs of damage;
- the ventilation slots are not obstructed.
STARTING AND STOPPING
- Starting
:move the switch lever (2) up; to lock it in "engaged" position,
move the switch block (3) forward towards the machine body.
- Stopping: : release the switch lever (2); if the switch is in "engaged"
position, move the switch lever (2) up in order to release the switch
block (3).
Warning! The tool continues to rotate after it is turned off.
Wait until it has come to a full stop before laying it down.
TEST RUN
Start the tool and check that there are no unusual vibration, no
dismatching of the buffer pad or of the abrasive disc.
Otherwise, switch-off the tool immediately and eliminate the cause.
ELECTRONIC SELECTING RPM (LH22EN - LH32EN)
The rpm can be adjusted by rotating the wheel (3). The choice of speed
depends on the characteristics of the abrasive disc and the material to be
worked.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rupes LH31 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rupes LH31 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info