489872

Rupes LE21A Manual

9
Zoom out
Zoom in
Previous page
1/34
Next page
9
SAFETY WARNINGS APPLICABLE TO POLISHING OPERATIONS
If the use of an electrical tool in a damp area cannot be avoided,
use a power supply fitted with a differential switch (RCD).
This type of switch reduces the risk of electrical shocks.
PARTS OF THE TOOL
1 - Identification plate
2 - ON/OFF switch
3 - Electronic rpm regulation (LE21AEC - LS21AE)
4 - Base plate
5 - Velcroed drilled rubber plate
6 - Paper clamping lever (LE21AC-LE21AEC)
7 - Motor ventilation slots
8 - 29 mm Ø suction port
9 - Dust bag
STARTING UP
Before starting-up the tool, ensure that:
- the packaging is complete and does not show signs of having been
damaged during storage or transport;
-the tool is complete; check that the number and type of
components comply with that reported in this instruction booklet;
- the power supply and socket outlet can support the load reported in
the table and that indicated on the tool identification plate
reproduced and explained on page 11.
ASSEMBLING THE TOOL
Fit the dust bag (9).
INSERTING THE ABRASIVE PAPER
LE21AC - LE21AEC
- Lift the paper clamping lever (6) by pressing the lever release;
- insert the abrasive paper under the lever until it rests against the
stop, then release the lever;
- repeat this operation on the opposite side of the plate, keeping the
paper taut and checking that the edges are parallel with the edges
of the plate before releasing the lever.
LE21A - LS21A - LS21AE
- Press the velcro backed abrasive paper in position, ensuring that
the holes in the paper coincide with the suction holes in the rubber
plate;
- make sure that there is no dust or other matter on the drilled rubber
plate.
BEFORE STARTING THE TOOL
Ensure that:
- the power supply conforms with the characteristics of the tool;
- the power supply cable and plug are in perfect condition;
- the ON/OFF switch works properly though with the power supply di-
sconnected;
- all the parts of the tool have been assembled in the proper manner
and that there are no signs of damage;
- the ventilation slots are not obstructed (7);
- the dust bag is enipty and not torn.
STARTING AND STOPPING
- Starting:
press the switch (2) down in position “I”.
- Stopping:
press the switch (2) up in position “O”.
TEST RUN
Start the tool and check that there are no unusual vibrations and that
the paper is kept taut.
Otherwise, switch-off the tool immediately and eliminate the cause.
REPLACING ABRASIVE PAPER
LE21AC - LE21AEC
- Lift the paper clamping lever (6) by pressing the release device and
remove the used paper;
- insert the new abrasive paper following the instructions in the
chapter on “INSERTING THE ABRASIVE PAPER”.
LE21A - LS21A - LS21AE
- Rip off the used paper;
- press the new velcro backed paper in position, ensuring that the ho-
les in the paper coincide with the suction holes in the plate.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rupes LE21A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rupes LE21A in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info