Manual Rupes GL040 (page 8 of 30) (English, German, Dutch, French, Italian, Spanish)

489862

Zoom out

Zoom in

1/30

PARTS OF THE TOOL

1 - Identification plate

2 - ON/OF switch

2A - Switch locking button

3 - Locking button for spindle shaft

4- Spindle

5 - Auxiliary handle

6 - Adjustable guard (GL080-GL080E)

7 - Collar with juts to fix the guards (GL080-GL080E)

8 - Screws to fix the guards (GL080-GL080E)

9 - Spacer

10 - Locking ring

10A - Tapered ring nut (GL040-GL040E)

11 - Motor ventilation slots

12 - Wrenches (17 mm spanner and pin spanner)

13 - Abrasive disc holder (GL040-GL040E)

14 - Electronic rpm regulation (GL040E-GL080E)

STARTING UP

Before starting-up the tool, ensure that:

- the packaging is complete and does not show signs of having been

damaged during storage or transport;

- the tool is complete; check that the number and type of components

comply with that reported in this instruction booklet;

- the power supply and socket outlet can support the load reported in

the table and that indicated on the tool identification plate reproduced

and explained on page 11.

ASSEMBLING THE TOOL

(GL080-GL080E)

- Fit the guard (6) onto the machine body using the screws (8), then in-

sert the collar (7) verifying that the juts on the collar are aligned with the

slots on the protection flange. Verify that the guard is placed next to

the handle.

- After fitting the screws (8) and collar (7), verify that the guard can be

turned with a slight friction by approximately 20°, thus making work mo-

re comfortable for the operator;

- screw in the auxiliary handle (5); the handle can be mounted on the left

or right of the tool body.

FITTING ABRASIVE WHEEL (GL080-GL080E)

1. Insert the spacer (9).

2. insert the abrasive wheel;

3. Firmly tighten the locking ring (10) with the adjustable wrench, kee-

ping the spindle shaft (4) in place with the 17 mm wrench or the

locking button (3).

FITTING THE DISC HOLDER AND THE FIBER-COATED DISC (GL040-GL040E)

1. Insert the spacer (9).

2. Fit the disc holder (14) onto the spindle shaft (4).

3. Assemble the fiber-coated disc.

4. Tighten the tapered ring nut (10A) and lock it with the adjustable

wrench (13), keeping the spindle shaft (4) in place with the 17 mm

wrench or the locking button (3).

BEFORE STARTING THE TOOL

Ensure that:

- the power supply conforms with the characteristics of the tool;

- the power supply cable and plug are in perfect condition;

- the ON/OFF switch works properly though with the power supply

disconnected;

- verify that the shaft locking button (3) is disabled. To perform this check,

manually rotate the grinding wheel or disc-holder by at least one revolution;

- all the parts of the tool have been assembled in the proper manner and

that there are no signs of damage;

- the ventilation slots are not obstructed.

STARTING AND STOPPING

- Start

: press the locking button (2A) on the upper section of the handle,

then the switch lever (2). To lock the spindle shaft in order to be able to

carry out a continuous machining, press the switch lever (2), then the

locking lever (2A) and hold it down while releasing the switch lever (2),

so that is firmly maintained in position.

- Stop

: release the switch lever or, if this is blocked, push the lever in

order to release the locking button.

TEST RUN

Start the tool and check that there are no unusual vibration, no dismatching

of the wheel.

Otherwise switch-off the tool immediately and eliminate the cause.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Rupes GL040 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Rupes GL040 Manual

Product: