489835

Rupes BA215N Manual

9
Zoom out
Zoom in
Previous page
1/34
Next page
9
PARTS OF THE TOOL
1 - Identification plate
2 - ON/OF switch
3 - Wheel spindle locking button
4 - Wheel spindle
5 - Auxiliary handle
6 - Adjustable protective shield
7 - Collar with protective shield fixing points
8 - Protective shield fixing screws
9 - Wheel mounting ring
10 - Abrasive wheel lock nut
11 - Motor ventilation slots
12 - Wrenches (17 mm spanner and pin spanner)
STARTING UP
Before starting-up the tool, ensure that:
- the packaging is complete and does not show signs of having
been damaged during storage or transport;
-the tool is complete; check that the number and type of
components comply with that reported in this instruction
booklet;
-the power supply and socket outlet can support the load
reported in the table and that indicated on the tool identification
plate reproduced and explained on page 11.
ASSEMBLING THE TOOL
- Mount the protective shield with collar (7) on the body of the tool
using the screws (8). Ensure that the protrusions on the collar
are inserted in the slots cut into the flange of the shield.
The shield must be mounted around the handle;
- after tightening the screws (8) and collar (7), the shield must be
able to rotate with a slight resistance approximately 20° in order
that it may be positioned as desired by the operator;
- screw in the auxiliary handle (5); the handle can be mounted on
the left or right of the tool body.
FITTING ABRASIVE WHEEL
1. Insert the wheel guide ring (9);
2. insert the abrasive wheel;
3. screw and tighten the lock nut (10) using the pin wrench, pre-
venting the spindle form moving using the 17 mm. spanner or
the spindle locking button.
BEFORE STARTING THE TOOL
Ensure that:
- the power supply conforms with the characteristics of the tool;
- the power supply cable and plug are in perfect condition;
-the ON/OFF switch works properly though with the power
supply disconnected;
- the wheel spindle locking button (3) is released (rotate the
abrasive wheel by hand for at least one revolution);
- all the parts of the tool have been assembled in the proper
manner and that there are no signs of damage;
- the ventilation slots are not obstructed.
STARTING AND STOPPING
- Starting
: push the slide of the switch (2) forward; if the tool is to
be locked in the ON position, apply pressure to the front part of
the slide switch at the same time.
- Stopping
: release the slide or, if locked in position, apply pres-
sure to the back part of the switch and allow it to return to the
stop position.
TEST RUN
Start the tool and check that there are no unusual vibration, no
dismatching of the wheel.
Otherwise switch-off the tool immediately and eliminate the
cause.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rupes BA215N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rupes BA215N in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info