Manual Ruby Fires TT5400 (page 5 of 12) (English, German, Dutch, French)

531524

Zoom out

Zoom in

1/12

Operation

The controls are located at the bottom right hand corner of the

appliance - see ‘z’ in Fig. 1.

Connect the re to your electricity supply.

Note: When either the remote control or the manual controls

are used the neon’s will come on for 3 seconds indicating the

appropriate setting - see Fig. 3.

Manual Operation

Note: The Standby Switch (see ‘a’ in Fig. 5) must be rst turned

on to operate either the manual or the remote controls. The red

indicator mark on the switch will be visible when it is turned on.

Setting Operation Indication

Flame effect Press the ‘I’ button once Left Neon

Flame effect & 750W heat setting Press the ‘

I’ button again Left & Middle Neon

Flame effect & 1500W heat setting Press the ‘

I’ button again All 3 neon’s

To turn off any of the settings press the ‘O’ button once.

To increase or decrease the brightness of the fuel effect use the

buttons ‘ ’ as shown in Fig. 5.

Remote Control

Note: The remote control is packed separately in the carton.

1. Slide open the battery cover on the back of the remote

transmitter.

2. Install the AAA batteries into the remote control (see

Fig. 4

3. Replace battery cover.

Dispose of batteries in the proper manner according to Provincial

and local regulations. Any battery may leak electrolyte if mixed with

a different battery type, if inserted incorrectly, if all the batteries are

not replaced at the same time, if disposed of in a re or if an attempt

is made to charge a battery not intended to be recharged.

Remote Control Operation

Warning: It takes some time for the receiver to respond to the

transmitter. Do not press the buttons more than once within two

seconds for correct operation.

Setting Operation Indication

Flame effect Press the ‘I’ button once Left Neon

Flame effect & 750W heat setting Press the ‘

I’ button again Left & Middle Neon

Flame effect & 1500W heat setting Press the ‘I’ button again All 3 neon’s

To turn off any of the settings press the ‘O’ button once.

To increase or decrease the brightness of the fuel effect use the

buttons ‘ ’ as shown in Fig. 4.

Lamp Replacement

To gain access to the lamps:

1. Remove the front glass by removing the three screws in the

glass retaining bracket (see Fig. 6 step 1)

2. Taking care tilt the glass and lift up to remove as shown in

Fig. 6 steps 2 & 3.

3. Remove the three screws in the middle of the fuel effect and

slide the the fuel effect out, by holding the front ledge and set

aside carefully (taking care not to damage the logs as they

are fragile) as shown in Fig. 6 step 4.

4. For access to the bulbs, carefully rotate the exible rotisserie

out of position ensuring that the rubber grommet is not lost

(see Fig. 7).

5. Unscrew the defective lamp anti-clockwise. Replace with a

230V, 60W E14 lamp, do not over tighten (see Fig. 7).

6. Refit the fuel effect and the front glass (using the six

screws).

- 2 -

Thermal Safety Cut-out

For your safety, this appliance has been tted with thermal cut-out.

In the event that the product overheats, the cut-out switches the

heat off automatically.

To bring the heat back into operation, remove the cause of the

overheating, then unplug or turn off the electrical supply to the

heater for up to 10 minutes.

When the heater has cooled sufciently, re-connect and switch

on the heater.

Caution: In order to avoid a hazard due to inadvertent resetting of

the thermal cut-out, this appliance must not be supplied through

an external switching device, such as a timer, or connected to a

circuit that is regularly switched on and off by the utility.

Cleaning and Maintenance

Warning: Always disconnect from the power supply before

attempting any maintenance.

Cleaning

Before commencing cleaning, unplug the heater and allow it to

cool.

The surface of the heater should be given an occasional wipe over

with a soft damp cloth. Do not use detergents abrasive cleaning

powder or polish on the body of the heater. The glass screen

should be cleaned carefully with a chamois leather. Do not use

proprietary glass cleaners.

Recycling

For electrical products sold within the European Community.

At the end of the electrical products useful life it should

not be disposed of with household waste. Please recycle

where facilities exist. Check with your Local Authority or

retailer for recycling advice in your country.

After Sales Service

Should you require after sales service, please get in touch with the

supplier through whom you purchased the appliance.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ruby Fires TT5400 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ruby Fires TT5400 Manual

Product: