763071
40
Zoom out
Zoom in
Previous page
1/49
Next page
78 79
FAULT SOLUTION
Cannot start the robot Make sure the robot is connected to power supply.
Make sure the battery is fully charged.
The robot suddenly stops working
Check whether the robot is stuck or blocked by obstacles.
Check whether the battery is too low.
If the problem persists, please shut it down, wait for 3 seconds, and then restart it.
The appliance may be overheating :
ū Stop the appliance and leave cool for at least 1 hour.
ū If it overheats on repeated occasions, contact the Approved Services Centre.
Cannot charge the robot
Check whether the indicator on the charging dock is on (when the robot is not on
the charging dock).
If not, check that the charger is properly connected or contact an Approved
services Centre to change the charger.
Check whether the indicator on the charging dock is o and the indicator on the
robot is ashing during charging.
Wipe dust o charging electrodes with dry cloth.
The charger is getting hot This is perfectly normal. The vacuum cleaner can remain permanently connected to
the charger without any risk.
The robot cannot return to the
charging dock
Clear the charging dock of objects within 0.5m on the left and right sides and
within 1.5m ahead.
Make sure that the robot starts cleaning from the charging dock without abnormal
movement.
When the robot is near the charging dock, it can return faster. But if the charging
dock is located far away, the robot will need more time to return. Please wait during
its return.
Clean charging electrodes.
The cleaning schedule is not
executed
Make sure the robot has been powered on.
Set the time and schedule the time for automatic cleaning with the app.
Make sure the appointment time has been set correctly.
Check whether the battery level is too low to start cleaning.
The robot will not start any scheduled cleaning when the task is being performed.
Suction whistling
Check the suction inlet for any obstruction.
Empty the dust box.
Clean lters.
Check whether lters are wet due to water or other liquids on the oor. Let lters
dry naturally thoroughly before use.
The dust collector is not properly tted :
ū re-position it correctly.
The intake head is clogged :
ū remove the power-brush and clean it.
The rolling brush does not rotate Clean the rolling brush.
Check whether the rolling brush and the brush cover are installed correctly.
Abnormal action or sweep route of
the robot
Carefully clean the sensor with dry cloth.
Restart the robot.
No water released during mopping
Make sure there is enough water in the water tank.
Check whether the mop module is installed correctly.
Check whether the water outlet is blocked.
The robot cannot connect to your
Wi-Fi network
Ensure that your Wi-Fi router supports 2.4GHz and 802.11 b/g/n bands as this
equipment does not support 5GHz bands.
6. 6.
According to model: *
When the robot fails, the red indicator on the robot will blink. Please check on the App the
stated error code.
Error code Solution
Error 1: Collision bumper is stuck, please
check. The collision bumper is stuck. Please tap repeatedly to remove foreign matters.
Ifthere is no foreign matter, please relocate it and then start it.
Error 2: A wheel is stuck. Please check
whether any foreign matter is stuck in the
wheel, or move it to near its home position
to start it.
If any wheel is stuck, please check whether any foreign matter is stuck in the
wheel, or move it to near its home position to start it.
Error 3: A side brush is stuck, please check. The side brush may be entangled with foreign matters. Please clean and restart it.
Error 4: The rolling brush is stuck. Please
remove and clean it. The rolling brush may be entangled with foreign matters. Please remove and
clean it, its connections, its cover and the suction inlet.
Error 5: The robot is trapped. Please clear
obstacles around. The robot is trapped. Please clear obstacles around.
Error 6: The robot is trapped. Please move it
near its home position to start it. The robot may be suspended. Please relocate it and start. If the anti-drop sensor is
too dirty, it may also cause the fault. Please wipe the anti-drop sensor to eliminate
the fault.
Error 7: A wheel is suspended. Please move
it to near its home position to start it. A wheel is suspended. Please move it to near its home position to start it.
Error 8: The battery level is too low, and the
robot is about to shut down automatically.
Please charge it.
The battery level is too low, and the robot is about to shut down automatically.
Please charge it.
Error 10: Optical flow sensor dirty, Please
wipe it. The optical flow sensor is covered by dust. Please wipe it.
Error 11: The recharge sensor is blocked.
Please wipe it. The recharge sensor is covered by dust. Please wipe it.
Error 12: The follow-wall sensor is blocked.
Please wipe it. The follow-wall sensor is blocked. Please wipe it.
Error 13: The robot is tilted. Please put the
robot on the horizontal ground to start. The robot is tilted during startup. Please put the robot on the horizontal ground
to start.
Error 14: Please install the dust box and
filters back. Please install the dust box and filters back, and make sure that filters and the dust
box are installed in place. Then please restart the robot.
Error 17: Restricted area detected. Please
relocate it to start. The robot is too close to a restricted area during starting. Please relocate it to start.
Error 18: The laser cover is stuck. Please
check. The pressure sensor for laser cover is pressed or stuck. Please relocate it to start.
Error 19: The laser sensor is stuck or twisted,
please check. The laser distance sensor is stuck by foreign matter. Please clear it.
Error 20: The laser sensor may be blocked,
please check. The laser distance sensor is blocked, please clear the blocking. Too spacious
environment and multi-reflection environment such as metal mirrors also affect
the normal operation of a laser distance sensor. Please relocate it to art.
Error 21: Please clear obstacles around the
charging dock. The robot may be stuck or trapped. Please clear obstacles around the robot.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rowenta RR7987 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rowenta RR7987 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 7,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info