763053
37
Zoom out
Zoom in
Previous page
1/48
Next page
7372
6.
Error codes
According to model: *
When the robot fails, the red indicator on the robot will blink. Please check on the App the stated error code.
Error code Solution
Error 1: Collision bumper is stuck, please
check. The collision bumper is stuck. Please tap repeatedly to remove foreign matters. If
there is no foreign matter, please relocate it and then start it.
Error 2: A wheel is stuck. Please check
whether any foreign matter is stuck in the
wheel, or move it to near its home position
to start it.
If any wheel is stuck, please check whether any foreign matter is stuck in the
wheel, or move it to near its home position to start it.
Error 3: A side brush is stuck, please check. The side brush may be entangled with foreign matters. Please clean and restart it.
Error 4: The rolling brush is stuck. Please
remove and clean it. The rolling brush may be entangled with foreign matters. Please remove and
clean it, its connections, its cover and the suction inlet.
Error 5: The robot is trapped. Please clear
obstacles around. The robot is trapped. Please clear obstacles around.
Error 6: The robot is trapped. Please move it
near its home position to start it. The robot may be suspended. Please relocate it and start. If the anti-drop sensor is
too dirty, it may also cause the fault. Please wipe the anti-drop sensor to eliminate
the fault.
Error 7: A wheel is suspended. Please move
it to near its home position to start it. A wheel is suspended. Please move it to near its home position to start it.
Error 8: The battery level is too low, and the
robot is about to shut down automatically.
Please charge it.
The battery level is too low, and the robot is about to shut down automatically.
Please charge it.
Error 10: Optical flow sensor dirty, Please
wipe it. The optical flow sensor is covered by dust. Please wipe it.
Error 11: The recharge sensor is blocked.
Please wipe it. The recharge sensor is covered by dust. Please wipe it.
Error 12: The follow-wall sensor is blocked.
Please wipe it. The follow-wall sensor is blocked. Please wipe it.
Error 13: The robot is tilted. Please put the
robot on the horizontal ground to start. The robot is tilted during startup. Please put the robot on the horizontal ground
to start.
Error 14: Please install the dust box and
filters back. Please install the dust box and filters back, and make sure that filters and the dust
box are installed in place. Then please restart the robot.
Error 17: Restricted area detected. Please
relocate it to start. The robot is too close to a restricted area during starting. Please relocate it to start.
Error 18: The laser cover is stuck. Please
check. The pressure sensor for laser cover is pressed or stuck. Please relocate it to start.
Error 19: The laser sensor is stuck or twisted,
please check. The laser distance sensor is stuck by foreign matter. Please clear it.
Error 20: The laser sensor may be blocked,
please check. The laser distance sensor is blocked, please clear the blocking. Too spacious
environment and multi-reflection environment such as metal mirrors also affect
the normal operation of a laser distance sensor. Please relocate it to art.
Error 21: Please clear obstacles around the
charging dock. The robot may be stuck or trapped. Please clear obstacles around the robot.
6.
Error W1: Battery abnormal. Please consult
the instructions or APP. Please open the battery compartment, check whether the battery is properly
connected, and try to restart the robot. The battery temperature is too high or too
low. Please wait for the battery temperature to be normal (0 °С~40 °С/32 °F~104
Error W2: Wheel module abnormal. Please
consult the instructions or APP. Please check whether any foreign matter is stuck in a wheel and try to restart the
robot. If the error persists, please contact our Service Department.
Error W3: Side brush module abnormal.
Please consult the instructions or APP. Please check whether any foreign matter is stuck in a side brush and try to restart
the robot. If the error persists, please contact our Service Department.
Error W4: Rolling brush abnormal. Please
consult the instructions or APP. Please remove and clean it, its connections, its cover and the suction inlet. Please
try to restart the robot after cleaning. If the error persists, please contact our
Service Department.
*Error W5: Water pump abnormal. Please
consult the instructions or APP. Please clean the water tank, water pump connections on the tank and water
pump connections on the robot, the water outlet at the robot bottom, and check
the mop module. Please try to restart the robot with all modules installed back
after cleaning. If the error persists, please contact our Service Department.
Error W6: Laser sensor abnormal. Please
consult the instructions or APP. Please check the laser sensor for foreign matter and try to restart the robot after
cleaning. If the error persists, please contact our Service Department.
Error W7: Fan abnormal. Please consult the
instructions or APP. Please check whether any foreign matter is stuck in the fan and try to restart the
robot. Please clean the dust box and filters and try to restart the robot. If the error
persists, please contact our Service Department.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rowenta RR7647 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rowenta RR7647 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 9,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info