762740
16
Zoom out
Zoom in
Previous page
1/71
Next page
12
* According to model : These parts are specific to certain
models or they are accessories that can be purchased se-
parately.
TROUBLESHOOTING
If your vacuum cleaner will not start
• The appliance is not plugged in. Check that the appliance is
plugged in correctly.
If your vacuum cleaner has no suction power
• Either an accessory or the hose tube is partially blocked:
unblock the accessory or the hose tube.
• The lid is not properly closed: check that the dust box is well
placed and close the lid.
If your vacuum cleaner has less suction power, is noisy or
makes a whistling noise
• Either an accessory or the hose tube is partially blocked:
unblock the accessory or the hose tube.
• The dust compartment is full: empty it (see CLEANING AND
MAINTENANCE chapter).
• The filtration system is saturated: clean the HEPA filter
capsule (16) (see CLEANING AND MAINTENANCE chapter).
If the problem persists, change the filtration system (see the
CLEANING AND MAINTENANCE chapter).
• Make sure that the dust box (12) is well positioned in the dust
tray housing (11).
• The mechanical power regulator (18b) is open: close the
mechanical power regulator on the butt.
• The electronic power regulator (9) is set at minimum:
increase the power using the electronic power regulator
(unless you are cleaning fragile fabrics).
If the lid does not close (detector action 14*)
• Verify that the HEPA filter case (16) is there and that it is
correctly positioned.
• Make sure that the dust box (12) is correctly positioned in the
dust tray housing (11).
If it is difficult to move the nozzle
• Reduce the power by opening the mechanical power control
on the butt (18b) or by moving the electronic power control
switch (9) towards the MIN position.
• Make sure that the position of the nozzle (20 or 21)
corresponds to the floor being vacuumed:
- for rugs and carpets, use the nozzle in the retracted brush
position,
- for parquets and smooth surfaces, use the nozzle in the
exterior position.
If the power cord does not wind completely
• The cord slowed down as it was winding up: pull the power
cord out again and press the power cord rewind pedal.
If a problem persists, take your vacuum cleaner to your local
Rowenta Authorised Service Centre or contact the Rowenta
Customer Service.
IMPORTANT If you notice that your vacuum
cleaner is not operating as well, before carrying out
any checks, switch it off using the ON/OFF pedal.
This appliance is designed for indoor domestic household
use only. In case of professional use, inappropriate use or
failure to comply with the instructions, the manufacturer
accepts no responsibility and the guarantee does not apply.
Always read the instructions carefully before using your
appliance for the first time: use that does not conform to the
instructions will release Rowenta from all liability.
GUARANTEE
EN
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rowenta RO6262 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rowenta RO6262 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 3,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info