Manual Rowenta DG8035 (page 8 of 46) (English, German, Dutch, French, Italian, Portuguese, Spanish)

739515

Zoom out

Zoom in

1/46

Problems Possible causes Solutions

The thermostat light and the

on/off switch are not lit.

The appliance is not switched

on.

Check that your appliance is correctly plugged in

and press the illuminated on/off switch (on the

front of the base-unit).

Water runs through the

holes in the soleplate.

You are using the steam

control button before the iron

is hot enough.

Decrease the steam output while ironing at low

temperature (steam output control dial on the

control panel).

Wait for the thermostat light to go out before

activating the steam control button.

Water has condensed in the

pipes because you are using

steam for the first time or you

have not used it for some

time.

Press the steam control button away from your

ironing board until the iron produces steam.

White streaks come through

the holes in the soleplate

Your boiler has a build-up of

scale because it has not been

rinsed out regularly.

Rinse out the boiler after every 10 uses, when

the orange indicator light flashes (see chapter

11). If your water is hard increase the frequency.

You have already rinsed the

boiler and the orange “boiler

rinse” light is flashing.

You have not pressed the

“Restart” button

Press the “Restart” button to turn off the

indicator light.

Brown streaks come through the

holes

in the soleplate and

stain the linen.

You are using chemical

descaling agents or additives

in the water for ironing.

Never add this type of product in the

water tank or

in the boiler (see our recommendations

regarding water to be used).

Your linen is not rinsed

sufficiently or you have

ironed a new garment before

washing it.

Ensure linen is rinsed thoroughly to remove

any

soap deposits or chemicals on new garments

which have been sucked up by the iron.

The soleplate is dirty or

brown and may stain the

linen.

You are ironing at too high a

temperature.

See our recommendations regarding

temperature control setting.

There is no steam. The

water tank is empty

(light turn on)

Fill the water tank and

press the “Restart” button

on the control panel.

There is little steam. The steam output control dial

is set at minimum.

Increase the steam output (control dial on the

control panel).

The soleplate temperature is set

to the maximum.

The generator is working but steam is very hot and

dry. As a consequence, it is less visible.

Water streaks appear on

the linen

Your ironing board is

saturated with water because

it is not suitable for use with a

steam generator.

Check that your ironing board is suitable. A

mesh type ironing board must be used to allow

any excess steam to escape and to avoid steam

venting sideways.

The red “removable water

tank empty” light is on.

You have not pressed the

“Restart” button

Press the “Restart” button on the control panel.

Steam escapes from the

rinse plug.

The rinse plug has not been

tightened correctly.

Tighten the rinse plug correctly.

The rinse plug seal is

damaged

Contact an Approved Service Centre to order

a new rinse plug seal.

Steam escapes under the

appliance.

The generator is faulty. Stop using the generator and contact an

Approved Service Centre

The power cord does not

fully retract.

The power cord has lost

tension during retraction.

Pull the power cord out completely. Press the

button and guide the cord with your free hand.

HELPLINE

If you have any product problems or queries with your product, please telephone our Customer Relations team on:

0845 602 1454 (UK) (Calls charged at local rate) - (01) 461 0390 (Ireland)

Consult our web site: www.rowenta.co.uk

Environment protection first !

Your appliance contains valuable materials which can be recovered or recycled.

 Leave it at a civic waste disposal centre.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Rowenta DG8035 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 6,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Rowenta DG8035 Manual

Product: