7.6 Press the “ENTER” button.
7.7 Enter your new Master Code (between 4 and 6
digits).
7.8 Press the “ENTER” button.
7.9 For confirmation re-enter the new Master Code of
your choice.
7.10 Press the “ENTER” button.
7.11 When the programming is successful, a double [2x]
acoustic signal will sound and the green LED
will flash twice [2].
7.12 The programming is now successfully completed.
If the input after typing “ENTER” was correct, a double
[2x] acoustic signal will beep and the green LED will flash
twice [2].
If the inputs after typing “ENTER” were incorrect, a triple
[3x] acoustic signal will beep and the red LED will flash
three [3] times. Start the programming again.
8. PROGRAMMING THE USER CODE
The User Code which you have selected will remain in-
tact, even if the batteries are changed. The selected User
Code can be changed any time (see CHANGING THE
USERCODE). For each of the following steps the pause
when pressing the buttons should be no longer than five
[5] seconds, otherwise the programming will be aborted.
Check your new code several times while the door is
opened. Close the door only when you are sure that the
new saved code works correctly.
8.1 Press the “*” button.
8.2 Press the “Enter” button.
8.3 Press the “2” button.
8.4 Press the “Enter” button.
8.5 Enter the valid Master Code.
8.6 Press the “Enter” button.
8.7 Enter your desired User Code (between 4 and 6
digits).
8.8 Press the “Enter” button.
8.9 For confirmation enter your chosen User Code
again.
8.10 Press the “Enter” button.
8.11 When the programming has been successfully com-
pleted, a double [2x] acoustic signal will sound
and the green LED will flash twice [2].
8.12 The User Code programming has now been
successfully completed.
If the input after typing “ENTER” was correct, a double
[2x] acoustic signal will beep and the green LED will flash
twice [2].
If the input after typing “ENTER” was incorrect, a triple
[3x] acoustic signal will beep and the red LED will flash
three [3] times. Start the programming again.
9. CHANGING THE USER CODE
The User Code that you select will remain unaltered, even
if you change the batteries. Think about your User Code
in advance. For each of the following steps a break when
pressing the buttons should be no longer than five [5]
seconds, otherwise the programming will be aborted.
Check your newly programmed code several times while
the door is open. Close the door only when you are sure
that the new code works correctly.
9.1 Press the “*” button.
9.2 Press the “ENTER” button.
9.3 Press the “3” button.
9.4 Press the “ENTER” button.
9.5 Enter the valid User Code.
9.6 Press the “ENTER” button.
9.7 Enter your desired User Code (between 4 and 6
digits).
9.8 Press the “ENTER” button.
9.9 To confirm, enter your chosen User Code again.
9.10 Press the “ENTER” button.
9.11 If the programming is successful, a double [2x]
acoustic signal will sound and the green LED will
flash twice [2].
9.12 The programming of the new User Code has now
been successfully completed.
If the input after typing “ENTER” was correct, a double
[2x] acoustic signal will beep and the green LED will flash
twice [2].
If the input after typing “ENTER” was incorrect, a triple
[3x] acoustic signal will beep and the red LED will flash
three [3] times. Start the programming again.
10. DELETING THE USER CODE
The saved User Code can be deleted using the Master
Code.
10.1 Press the “|*” button.
10.2 Press the “ENTER” button.
10.3 Press the “0” button.
10.4 Press the “ENTER” button.
10.5 Enter the valid Master Code.
10.6 Press the “ENTER” button.
10.7 The User Code is now deleted.
If the input after typing “ENTER” was correct, a double
[2x] acoustic signal will beep and the green LED will flash
twice [2].
If the input after typing “ENTER” was incorrect, a triple
[3x] acoustic signal will beep and the red LED will flash
three [3] times. Start the programming again.
Attention:
Your new Safe and it’s content aren’t
automatically insured.
Please write a letter to your
insurance about the insurance value
you’d like.
SYDNEY Electronic Safe 6
