489959

Rotel RT12 Manual

11
Zoom out
Zoom in
Previous page
1/20
Next page
11
English
DIGITAL INPUT-AUX
t
The unit can receive digital music signal from other sources and convert
them to analog signals then output to a pre-amplifier or processor connected
through OUTPUT
e
jacks. There are two connector on the AUX Digital
Input area on the rear panel, labeled with coaxial and optical. Connect
the coaxial or optical output of your source to the coaxial or optical
input of the unit.
Network Connection
qr
This unit can connect to a wired or wireless network. If using a wired
network, connect your internet cable to the socket marked ETHERNET
q
.
If using a wireless network, please connect the WiFi antenna (supplied)
to the connector marked WiFi
r
.
UPGRADE USB mini socket
y
The software of this unit can be updated through this socket, if upgrades
become necessary.
OUTPUT
e
The unit outputs a stereo analog signal. Use the supplied audio cable to
connect it with input jacks of your pre-amplifier or processor. Be careful
and make sure that connections correspond to each other. Right channel
output must be connected to right channel of pre- amplifier’s or processor’s
right channel and vice versa.
ROTEL LINK
u
These 2 Rotel Link Out connections can be made with the stereo 3.5 mm
cable (supplied) to a Rotel integrated amplifier and CD player. These
connections link the Digital Gateway, Amplifier and CD player into one
IP controllable system via the Rotel Remote application. See Figure 3.
Internet Radio
What you need before starting
Before you can use your Internet radio, you need the following:
A broadband Internet connection. •
Access point to internet through wired or wireless LAN. •
With wireless LAN connection, internet radio should work within 100
metres of the wireless access point, subject to the router/Wi-Fi gateway
being placed in the optimum area for your location. The user can confirm
the WiFi Strength under the settings menu. (Settings-->WiFi Strength)
Make sure that your LAN is connected properly and is able to access
the internet. To access internet radio stations an internet connection is
required.
First Time Connection To The Network
When you turn on the unit for the first time, it starts by searching for LAN
connections. If both wired and wireless connections are present, the
wired connection will be the default, unless a “wireless only” selection
was made in the setup menu. The following example illustrates a wireless
connection.
Starting ... ...
SCANNING NETWORK.. ...
After a few seconds, it will start to scan for networks.
If no wireless network is found, it will display no network found.
NO NETWORK FOUND
When the unit finds your network, it will display the ESSID for the access
point on the screen – this is a name that is allocated to the access point
by the person who set up the network – for example:
< MY NETWORK >
It is possible, and in some locations highly likely, that your unit will find
more than one wireless access point if using wireless connection, in which
case you can choose which one you want to connect to. Turn the knob on
the panel to see the ESSID for each access point the radio has found.
If the screen displays “Enter WEP key” or “Enter WPA key” then the network
is using one of the encryption systems, Wired Equivalent Privacy (WEP)
or Wi-Fi Protected Access (WPA). Please obtain the access code from
the person who set up your wireless network, or check the user manual
of your router for this information. Input the code into the Rotel unit to
gain access to the wireless LAN.
Note: If you would like to use a static IP address, or if the unit can not
automatically get an IP address, then please see the ‘Network config’
section under the ‘Settings’ section at the end of the manual.
… 11 …


Need help? Post your question in this forum.

Forumrules
1

Forum

rotel-rt12

Reset search

  • Hi, sontec electronics have just fitted me a new streaming module into my rotel RT12 and I need to know how to get internet radio, put in my wifi key and conected to my router but just get the message pura vida 106.3fm Buffering 0% please help Submitted on 10-10-2022 at 21:10

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rotel RT12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rotel RT12 in the language / languages: English as an attachment in your email.

The manual is 2,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info