Manual Rotel RT-06 (page 9 of 89) (English, German, Dutch, French, Italian, Spanish)

490029

Zoom out

Zoom in

1/89

English

OFF Button

Remote only

Pressing the OFF button places the RT-06 into

standby mode. Power is still supplied to the

unit, but functions are disabled.

Remote Sensor

This front panel sensor receives infrared sig-

nals from the remote control. Make sure you

do not accidentally block this sensor with

cables or accessories.

Front Panel Display

The large ﬂuorescent display in the center por-

tion of the RT-06 provides status information

used in operating the DAB/AM/FM receiver

(such as station frequency display, band pre-

set memory, RDS information, etc.)

MEMORY Button

The MEMORY button is used to conﬁrm and

memorize the various setting in the setup and

operation of the RT-06, including tuner sta-

tion presets. Its use is described in detail in

the relevant sections below.

ENTER Button

Pressing the ENTER button selects the high-

lighted parameter in the SETUP display.

SETUP Button

Opens and closes the RT-06 setup menu.

This provides the RT-06 setup menus as well

as the ability to change county modes by

using the front panel ENTER, UP/DOWN

Buttons.

DIMMER Button

Available on the front panel and remote con-

trol, this button selects four display brightness

settings. Press the button to cycle through the

four settings.

NOTE: When the tuner is turned off then back

on, the display reverts to its normal setting.

The dimmer setting is also available in the

SETUP menu for memory setup until the AC

line is disconnected.

Basic Tuning Controls

The RT-06 features a digital synthesized AM/

FM tuner with RDS or RBDS capability, 30-sta-

tion preset and a DAB tuner with a maximum

of 99 station presets.

• Manual frequency tuning lets you

tune up or down to the next station fre-

quency. Set the TUNE/PRESET mode to

TUNE. Turn off AUTO TUNING. Use the

TUNING controls to tune up or down.

• Direct frequency tuning lets you enter

the desired station frequency digits. Press

the FREQUENCY DIRECT button on the

remote or front panel and enter the digits

using the NUMERIC buttons.

• Automatic frequency search tun-

ing lets you search up or down to ﬁnd

the next available broadcast signal. Set

the TUNE/PRESET mode to TUNE. Turn

on AUTO TUNING. Use the TUNING

controls to search up or down.

• Memory station preset tuning lets

you directly enter the number of a mem-

orized station preset number. Enter the

number of the memorized preset using

the NUMERIC buttons for the AM/FM or

DAB band.

• Preset scan tuning lets you scan up/

down through the memorized station

presets. Press the PRESET SCAN button

to begin scanning the AM/FM bands.

• RDS (Europe) or RBDS (USA) tun-

ing provides a range of special tuning

and search features based on data codes

encoded with the broadcast signal. See

the RDS section of this manual for detailed

information.

TUNING Controls

A pair of buttons, labeled <TUNING> on the

front panel, and the “FREQ UP/DOWN” and

“PRESET UP/DOWN” buttons on the remote,

serve as the main tuning controls for the RT-

06. You can use either the front panel or re-

mote buttons; their function is identical. These

controls provide different tuning functions de-

pending on the mode of operation.

BAND Button

The BAND button selects whether the tuner

will receive DAB, AM or FM broadcast sig-

nals. Press the button to toggle back and forth

between DAB, AM and FM. A corresponding

indicator will light at the left portion of the

front panel DISPLAY to conﬁrm your choice.

The currently tuned station frequency will

be shown.

FREQUENCY TUNING mode

• With AUTO TUNING off, press a TUN-

ING button to manually jump to the next

frequency, regardless of whether or not a

station is broadcasting on that frequency.

[See the TUNE/PRESET button and AUTO

TUNING button sections for details on

changing the tuning modes.]

• With AUTO TUNING on, press a TUN-

ING button to start auto tuning. The tuner

begins automatically scanning up or down

through the frequencies until the next re-

ceivable signal is detected. If this is not

the desired station, repeat the automatic

tuning procedure to ﬁnd the next station.

Weak stations will be skipped during auto

tuning. If no receivable signal is detected,

the tuner will revert to the last previously

tuned station. [See the TUNE/PRESET but-

ton and AUTO TUNING button sections for

details on changing the tuning modes.]

PRESET TUNING mode

Press a TUNING button to advance to the

next memorized station preset. [See the

TUNE/PRESET button section for details on

changing the tuning modes.]

RDS PTY search mode

Press a TUNING button to select the desired

program type from the scrolling list in the

display. See the section on RDS tuning for

more details. [See the RDS PTY button sec-

tion for details.]

NOTE: Several indicators in the front panel dis-

play assist tuning. A large display shows the

tuned frequency and increases or decreases

during tuning. A signal strength indicator

shows the strength of an incoming signal. A

TUNED indicator lights when a sufﬁciently

strong signal is received. A ST indicator lights

when a stereo FM signal is received. In ad-

dition, indicators show the currently selected

tuning mode.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Rotel RT-06 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Rotel RT-06 Manual

Product: