498117
44
Zoom out
Zoom in
Previous page
1/46
Next page
44
RSX-1056 Surround Sound Receiver
To memorize USER DEFAULT settings:
Many of the current configuration settings can
be stored as a USER DEFAULT, which can be
activated at any time from this menu screen.
To save the current settings as a USER DEFAULT,
place the highlight on the SET USER DEFAULT
line using the UP/DOWN buttons and use the
+/– buttons to change the setting to YES. Press
the ENTER button to store the new USER DE-
FAULT settings. To return to the MAIN menu
without saving any changes, change all en-
tries on the screen to NO and press the EN-
TER button.
NOTE
: If there is insufficient memory to store a
USER DEFAULT configuration file, the SET
USER DEFAULT option will not be available.
To activate memorized USER DEFAULT
settings: After you have stored a USER DE-
FAULT configuration file, you can activate those
settings at any time by placing the highlight
on the USER DEFAULT line using the UP/
DOWN buttons. Use the +/– buttons to change
the setting to YES. Press the ENTER button to
proceed with activating the USER DEFAULT
settings. To return to the MAIN menu without
activating the USER DEFAULT settings, change
the entry to NO and press the ENTER button.
MORE INFORMATION
Troubleshooting
The unit does not turn on.
Make sure the power cord is plugged into
the rear panel and a live AC wall outlet.
Make sure the rear panel POWER switch
is in the ON position.
No sound from any input.
Make sure that MUTING is off and VOL-
UME is turned up.
Make sure that preamp outputs are con-
nected to a power amplifier and that the
amplifier is turned on.
Make sure source inputs are connected and
configured correctly.
No sound from digital sources.
Make sure that digital input connector is
assigned to the proper source input and
that the source input is configured to use
the digital input rather than an analog input.
Check the configuration of the DVD player
to ensure that the bitstream and/or DTS
digital output is activated.
No sound from some speakers.
Check all power amp and speaker con-
nections.
Check
Speaker Configuration
settings in
the
Setup
menus.
No video output on TV monitor.
Make sure that the TV monitor is connected
properly. Component video outputs can
send any type of signal to the TV. Com-
posite video connections can only send
video from composite sources and S-Video
connections can only send video from
S-Video sources.
Make sure the NTSC/PAL switch is set
properly.
OSD menus are not displayed on TV
Monitor.
Go to Setup menus and configure OSD
menus to be displayed on the TV monitor.
In some PAL systems, the menus may not
be displayed unless there is an active video
signal.
When using progressive scan video sig-
nals, make sure that the progressive mode
is selected for that video input in the OTHER
OPTIONS setup menu. This allows the dis-
play of the main setup OSD menus on the
TV monitor by interrupting the progressive
scan video signal and restoring it after the
OSD menus are cancelled. The temporary
information screens (such as volume, etc.)
cannot be displayed on the TV monitor when
progressive scan signals are being used.
Video and Audio do not match.
Check that the proper video source is se-
lected for each input.
Check that the group delay (lip-synch) setting
is not misadjusted.
Clicking or popping sounds when
switching inputs.
The unit uses relay switching to preserve
maximum sound quality. The mechanical
clicking of the relays is normal.
During switching, it may take a split sec-
ond for digital signals to be recognized
and properly decoded. Rapid repeated
switching between inputs or settings can
result in clicks or pops from the speakers
as the unit attempts to lock on to the rap-
idly changing signals. This causes no harm.
Controls do not operate.
Make sure that fresh batteries are installed
in the remote.
Make sure that the IR sensor on the front
panel is not blocked. Aim the remote at
the sensor.
Make sure the sensor is not receiving strong
IR light (sunlight, halogen lighting, etc.)
Unplug the unit from the AC outlet, wait
30 seconds, and plug it back in to reset.
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rotel RSX-1056 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rotel RSX-1056 in the language / languages: English as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info