577720
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
RDD-1580 Digital to Analog Converter
Fill out and send in the ownerÊs registration card packed with the RDD-1580.
Also be sure to keep the original sales receipt. It is your best record of the date
of purchase, which you will need in the event warranty service is required.
Placement
Like all audio components that handle low-level signals, the RDD-1580 can
be affected by its environment. Avoid placing the RDD-1580 on top of other
components. Also avoid routing audio signal cables near power cords. This
will minimize the chance it will pick up hum or interference.
We recommend installing the unit in furniture designed to house audio
components. Such furniture is designed to reduce or suppress vibration which
can adversely affect sound quality. Ask your authorized Rotel dealer for advice
about component furniture and proper installation of audio components.
The RDD-1580 is supplied with an RR-DD91 remote control and must be
placed where the infrared signal from the remote can reach the front panel
Remote Sensor.
Cables
Be sure to keep the power cords, digital signal cables and regular audio
signal cables in your installation away from each other. This will minimize
the chance of the regular audio signal cables picking up noise or interference
from the power cords or digital cables. Using only high quality, shielded
cables will also help to prevent noise or interference from degrading the
sound quality of your system. If you have any questions see your authorized
Rotel dealer for advice about the best cable to use with your system.
The RR-DD91 Remote Control
Some functions can be done with either the front panel controls, or the
supplied RR-DD91 remote control. When these operations are described,
the square call out numbers refer to the main unit, while the encircled letters
refer to the remote control.
Remote Control Batteries
Two UM-4/AAA size batteries (supplied) must be installed before the remote
control can be used. To install the batteries, remove the cover on the back of
the RR-DD91. Install the batteries as shown in the illustration in the battery
well. Test the control for proper operation, then replace the cover. When
the batteries become weak the remote control wonÊt operate the RDD-1580
consistently. Installing fresh batteries should eliminate the problem.
AC Power and Control
AC Power Input
-
Your RDD-1580 is configured at the factory for the proper AC voltage in
the country where you purchased it, either 120 volts or 230 volts. The AC
line configuration is noted on a decal on the back panel.
NOTE: Should you move your unit to another country, it may be possible to
reconfigure it for use on a different line voltage. Do not attempt to perform
this conversion yourself. Opening the enclosure of the unit exposes you to
dangerous voltages. Consult a qualified service person or the Rotel factory
service department for information.
NOTE: Some products are intended for sale in more than one country and
as such are supplied with more than one AC cord. Please use only the cord
appropriate for your country/region.
The RDD-1580 should be plugged directly into a 2-pin polarized wall outlet
or into the switched outlet on another component in your audio system. Do
not use an extension cord.
Connect the supplied power cord to the Power Connector
-
on the rear
of the unit and the AC power outlet. The Power indicator light is illuminated
if the unit is plugged in, it is in Standby mode.
If you are going to be away from home for an extended period of time such
as a month-long vacation, it is a sensible precaution to unplug the RDD-
1580 (as well as other audio and video components) while you are away.
Power Switch and Power Indicator
1
Press the front panel Power Switch button, to turn the unit on. One of the
input selector indicator light is illuminated when the unit is on. Press the
Power Switch button again, the unit is in Standby mode.
When the power indicator is illuminated, the remote control ON and OFF
buttons may be used to activate the RDD-1580.
NOTE: Place the self adhesive ring over the light surrounding the power
switch if the blue light is too bright.
Remote Sensor
3
This remote sensor window receives IR commands from the remote control.
Please do not block this sensor.
Front Input Indicators
4
The front panel has a set of indicators showing which input is currently selected.
PC-USB : This is the rear USB connection
COAX 1 and 2: Set of Coaxial inputs 1 or 2
OPT 1 and 2: Set of Optical inputs 1 or 2
USB : This is the front USB connection.
Sampling Frequency Indicators
5
The Sampling Frequency light will illuminate if the music being played
matches one of the Sampling Frequency indicators.
NOTE: Not all supported Sampling Frequencies have an indicator. Your
music may still play even if it does not have a light associated with the
sample rate of your audio.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rotel RDD-1580 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rotel RDD-1580 in the language / languages: English as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info