489962

Rotel RA12 Manual

10
Zoom out
Zoom in
Previous page
1/13
Next page
10
RA-12, RA-11 Stereo Integrated Amplifier
Speaker Connection
Turn off all the components in the system before connecting the speakers.
The amplifier has color-coded binding post type speaker connectors on
the back panel. These connectors accept bare wire, connector lugs, or
dual banana type connectors. (except in European Community countries
where their use is not permitted)
Route the wire from the amplifier to the speakers. Give yourself enough
slack so you can move the components to allow access to the speaker
connectors. If you are using dual banana plugs, connect them to the wires
and then plug into the backs of the binding posts. The thumbscrews of the
binding posts should be screwed in all the way (clockwise).
If you are using terminal lugs, connect them to the wires. If you are attaching
bare wires directly to the binding posts, separate the wire conductors
and strip the insulation from the end of each conductor. Be careful not
to cut into the wire strands. Unscrew (turn counterclockwise) the binding
post thumbscrews. Place the connector lug or wire around the binding
post shaft. Turn the thumbscrews clockwise to clamp the connector lug
or wire firmly in place.
NOTE: Be sure there are no loose wire strands that could touch adjacent
wires or connectors.
Phones Output
4
The Phones output allows you to connect headphones for private listening.
This output accommodates standard stereo phone (1/8”) plugs. Plugging
in a set of headphones does not cut off the signal to the outputs. Use the
Speaker Selector to turn off the speakers. The settings of the Function
Selector determines which source is heard.
NOTE: Because the sensitivity of speakers and headphones can
vary widely, always reduce the volume level before connecting or
disconnecting headphones.
Remote Sensor 5
This remote sensor window receives IR commands from the remote control.
Please do not block this sensor.
Display 7
The front panel display shows the source selected, volume level and
tone settings.
USB Input 0
The front USB input can be connected to a iPod, iPhone, MP3 players
or a Bluetooth dongle (supplied) for wireless streaming. With iPod
or iPhones, simply plug the device into the front USB and select USB
function from the source selector. The iPod, iPhone remains active.
Search and play tracks as usual and the music will be played through
the Rotel system.
Bluetooth Dongle
Insert the supplied Bluetooth Dongle into the front USB for wireless streaming
via Bluetooth, from your device (i.e. mobile phones) to the amplifier.
From your mobile device, look for “Rotel Bluetooth” and connect to it.
Connection is normally automatic, but if prompted for a password, please
press “0000” then press ENT on the remote and your device.
Audio Controls
Volume Control
9B
Turn the controls clockwise to increase the volume, or counter clockwise
to decrease the volume. From the remote control press the volume + or
- key to turn the volume up or down. Press the MUTE key to completely
mute the volume.
Balance Control
8C
The Balance Control adjusts the left-to-right balance of the sound output.
The factory default is the center position or “0”. To change the balance
from the front panel, press the MENU8 key to toggle the front display
to BALANCE SETTING mode. Then press the LEFT or RIGHT keys on the
front panel to change the value to LEFT or RIGHT. The value can change
from L15 to R15. From the remote, press the BALC key to access the
BALANCE SETTING menu, the press the LEFT or RIGHT key to adjust.
When finished, press the EXITG key to exit the menu.
Tone Control Bypass 8
F
Bass and Treble Control (Tone Control) circuits are bypassed at factory
default to ensure the purest possible sound. The front display will show
TONE BYPASS. To turn on the tone control, press the BYPASSF key
on the remote control. From the front panel press the MENU8 key to
toggle to the Bypass control then press the LEFT or RIGHT keys to turn
bypass on or off.
Bass and Treble Controls
8C
Set the Bass or Treble controls from the front panel by pressing the
MENU
8
key to toggle to either the Bass or Treble Setting menu. Then
press the LEFT or RIGHT key to adjust the value. The Bass and Treble
values range from -10 to +10. From the remote control, press the Bass
or Treble key
C
, then press the LEFT or RIGHT keys on the remote to
adjust the value.
A properly setup high-performance audio system produces the most
natural sound with little or no adjustment of the tone controls. Use these
controls sparingly. Be particularly careful when turning the controls up.
This increases the power output in the bass or treble range, increasing
the load on the amplifier and speakers.
NOTE: Setting the Bass and Treble controls do not automatically turn
on the tone control. To turn on tone control, refer to previous section
Tone Control Bypass.
Function Control
-L
The Function control selects the input signal source. From the front panel
or remote press the corresponding input key to select the source to listen
to.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rotel RA12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rotel RA12 in the language / languages: English as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info