489961
11
Zoom out
Zoom in
Previous page
1/13
Next page
11
English
ROTEL LINK
q
[See Figure
3
.]
This amplifier is capable of linking with other Rotel Link enabled
products in the series. Connect the 3.5mm cable from the ROTEL
Link Output of the Digital Gateway RT-12. This allows the unit to be
controlled through the IP remote developed by ROTEL.
12V Trigger Outlet
w
[See Figure
3
.]
Some audio components can be turned on automatically when they
receive a 12V turn on “signal”. The two12V Trigger Outputs of the RA-
11/RA-12 provide the required signal. Connect compatible components
to the amplifier with a conventional 3.5mm mini plug cable. When the
unit is turned off, the trigger signal is interrupted, and the components
controlled by it are turned off.
NOTE: If you are using other units in the series with Rotel link, please
use the Rotel Link connection to turn the units on or off. Do not connect
both the Rotel Link and 12V trigger cables. The 12V trigger’s power on
or off features will override the Rotel Link features.
Rear USB Upgrade=
The rear mini USB socket labeled UPGRADE is for updating the
internal firmware when necessary and should be handled by a
certified technician.
Protection Indicator
3
The amplifier has both thermal and over-current protection circuitry that
protects the amplifier against damage in the event of extreme or faulty
operating conditions. The protection circuits are independent of the
audio signal and have no impact on sonic performance. Instead, the
protection circuits monitor the temperature of the output devices and
shut down the amplifier if temperatures exceed safe limits.
Most likely, you will never see this protection circuitry in action. However,
should a faulty condition arise, the amplifier will stop playing and the
LED indicator on the front panel will light up.
If this happens, turn the amplifier off. Let it cool down for several minutes,
and attempt to identify and correct the problem that caused the protection
circuitry to engage. When you turn the amplifier back on, the protection
circuit will automatically reset and the indicator LED should go out.
In most cases, the protection circuitry activates because of a fault condition
such as shorted speaker wires, or inadequate ventilation leading to an
overheating condition. In very rare cases, highly reactive or extremely low
impedance speaker loads could cause the protection circuit to engage.
If the protection circuitry triggers repeatedly and you are unable to isolate
and correct the faulty condition, contact your authorized Rotel dealer for
assistance in troubleshooting.
Settings Menu
You can access the settings menu from the front panel by pressing the
MENU8 button or the SETUPD button on the remote. You can step
through a total of eleven sub-menus by pressing the MENU8 key on
the front panel or UP/DOWN key on the remote.
1. Bass (refer to Bass and Treble control section)
2. Treble (refer to Bass and Treble control section)
3. Balance (refer to Balance control section)
4. Tone Bypass (refer to Tone Control Bypass section)
5. Contrast: Changes the front panel display contrast between the back
light and the actual characters.
6. Dimmer: Dims the display in 7 steps. This can also be accessed
directly from the DIMI button on the remote control.
7. Rotel Link CD, selects how the CD player is connected to the amplifier,
either CD (analog), CX1 (coaxial 1) or CX2 (coaxial 2). CD is the
factory default.
8. POWER ON Volume: This sets the volume level when the unit is
turned ON.
9. Software Version : This shows the current software version loaded
into the amplifier.
10. Factory Reset RIGHT=Yes: This sets the unit back to the original
state as when it left the factory. Press the RIGHT key on the front panel or
remote control to perform a factory reset. The unit will ask for confirmation,
press the RIGHT key again to confirm. To cancel factory default at the
confirmation menu, press the Menu key or UP/DOWN key on the remote
to go to the next menu.
11. Exit: Exits the menu. Or from the remote press the EXITG key to
exit the menu at any time.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rotel RA11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rotel RA11 in the language / languages: English as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info