Manual Rossmax SB100 (page 2 of 2) (English)

783666

Zoom out

Zoom in

1/2

Introduction

Error code for your reference

Rossmax Fingertip Pulse Oximeter SB100 is used

to measure arterial oxygen saturation (% SpO2) of

hemoglobin and pulse rate, an important indicator

of your respiratory function. It is non-invasive device

intended for spot-check of adult and pediatric whose

age is over 3 at home, hospital.

Attention: Consult the accompanying

documents. Please read this manual carefully

before use. Please be sure to keep this manual.

SENSOR ERROR:

Sensor cannot be detected,

return the device to your

local distributor or service

centre.

MEASURE ERROR:

Signals cannot be detected,

turn the device off and

measure again.

Installing Batteries

1. Use thumb to slide battery

cover out

2. Insert or replace 2 “AAA” sized

batteries down with the

correct electrical polarity.

You need to replace the

batteries when

1. Battery icon is blinking on

display.

2. The function button is pressed

and nothing appears on

display.

Caution: Batteries may leak or explode if used or

disposed of improperly. Remove batteries if

the device will be stored for long time. Do

not use different types or brands of batteries

at the same time. Do not mix fully charged

and partially charged batteries at the same

time.

Attaching the lanyard

1. Insert the narrow end of

the lanyard through the

holder.

2. Draw the other end of the

lanyard through the loop

at the narrow end and

tighten.

How to use

1. Open the clip; press the Power On button as .

2. Information of software version appears; insert one

finger, nail side up, into the finger opening of the

pulse oximeter.

Note: if no finger insert, the device will auto shut off

after 8 seconds.

3. The pulse strength indication shows “ ”, pulse

oximeter begins its measurement as .

Note: make sure the finger is lying flat, Do not shake

and keep body steady during measurement as

.

4. Your SpO2 and pulse rate values will appear on the

screen after few seconds as .

Note: 1. Don’t remove your finger until the measurement

is completed.

2. If SpO2 and pulse rate cannot be detected, “

“ will appear on the screen as .

3. While pulse strength is low, the reading will

flicker.

Note:

1. The SpO2 sensor and photoelectric receiving tube

should be arranged in a way with the subject’s

arteriole in a position there between.

2. Make sure the optical path is free from any optical

obstacles like rubberized fabric.

3. Excessive ambient light may affect the measuring

result. It includes fluorescent lamp, dual ruby light,

infrared heater, direct sunlight and etc.

4. Strenuous action of the subject or extreme

electrosurgical interference may also affect the

accuracy.

Cautionary Notes

- This device is to be operated by trained personnel

only.

- This device has no audible and it intended only for

spot-checking, but not medical result evaluation.

- This device is designed to determine the percent-

age of arterial oxygen saturation of functional hemo-

globin. Factors that may degrade pulse oximeter per-

formance or aect the accuracy of the measurement

include the following:

• Do not apply the pulse oximeter on the same arm

as a blood pressure cu, arterial catheter or infusion

line(s)

• Excessive light, such as sunlight or direct home light-

ing.

• Not steady at the site of application (e.g. trembling)

• Moisture in the device

• Improperly applied device

• Finger is too large or too small to t into the device.

• Poor pulse quality

• Venous pulsations

• Anemia or low hemoglobin concentrations.

• Cardiogreen and other intravascular dyes

• Carboxyhemoglobin

• Methemoglobin

• Dysfunctional hemoglobin

• Articial nails or ngernail polish

• On ngers with anatomical changes, oedemas, scars

or burns.

- Using the device for long periods may cause pain

for people with circulatory disorders. Reposition the

device at least once every 4 hours to allow the pa-

tient’s skin to breath and to check patient’s condition

regularly.

- Do not use the device near ammable or explosive

gas mixtures.

- Do not use the device during an MRI or CT scan, be

used no closer than 30 cm (12 inches) to any part

of the [ME EQUIPMENT or ME SYSTEM], including ca-

bles specied by the manufacturer

- The device may not work when circulation is re-

duced. Warm or rub the nger, or re-position the

device.

- This device is a precision electronic instrument and

must be repaired by qualied technical profession-

als. Field repair of the device is not possible. Do no

attempt to open the case or repair the electronics.

Opening the case may damage the device and void

the warranty.

- Do not overextend the device’s spring.

- A functional tester cannot be used to access the ac-

curacy of a pulse oximeter monitor.

- Do not self-diagnose or self-medicate on the basis of

the measurements without consulting your doctor.

In particular, do not start taking any new medication

or change the type and/or dosage of any existing

medication without prior approval.

- Do not look directly inside the housing during the

measurement. The red light and the invisible infra-

red light in the pulse oximeter are harmful to your

eyes.

- This device is not intended for use by people (in-

cluding children) with restricted physical, sensory or

mental skills or a lack of experience and/or a lack of

knowledge, unless they are supervised by a person

who has responsibility for their safety or they receive

instructions from this person on how to use the de-

vice. Children should be supervised around the de-

vice to ensure they do not play with it.

- Neither of the displays for the pulse wave and pulse

bar allows the strength of the pulse or circulation to

1. SpO2 icon

2. Pulse strength

indication

3. Pulse rate icon

4. Beats per minute

5. Power On Button

6. Battery icon

7. Battery compartment

Name/ Functions of each part

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Rossmax SB100 in the language / languages: English as an attachment in your email.

The manual is 1.96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Rossmax SB100

Rossmax SB100 User Manual - German - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Rossmax SB100 Manual

Product: